110169
9
Zoom out
Zoom in
Previous page
1/13
Next page
Adjusting for bevel cuts (Fig. 6)
Loosen the thumb nuts in front and back, and tilt the
tool to the desired angle for bevel cuts (0 45°).
Secure the thumb nuts tightly in front and back after
making the adjustment. (5603R, 5703R, 5903R,
5103R)
Loosen the thumb nut in front and tilt the tool to the
desired angle for bevel cuts (0 60°). Secure the
thumb nut tightly in front after making the adjust-
ments. (5143R)
Sighting (5603R, 5703R) (Fig. 7)
For straight cuts, align the right notch on the front of
the base with your cutting line on the workpiece.
For 45° bevel cuts, align the left notch with it.
Top guide (5903R, 5103R) (Fig. 8)
Align your sight line with either the 0° notch for
straight cutting or the 45° notch for 45° angle cuts.
Top guide (5143R) (Fig. 9)
Align your sight line with either the 0° notch for
straight cutting or the 30° notch for 30° angle cuts or
the 45° notch for 45° angle cuts or the 60° notch for
60° angle cuts.
Switch action (Fig. 10)
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
press the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
CAUTION:
Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to
the ‘‘OFF’ position when released.
Operation (Fig. 11)
Hold the tool firmly. Set the base plate on the work-
piece to be cut without the blade making any contact.
Then turn the tool on and wait until the blade attains
full speed. Now simply move the tool forward over the
workpiece surface, keeping it flat and advancing
smoothly until the sawing is completed. To get clean
cuts, keep your sawing line straight and your speed of
advance uniform.
CAUTION:
The riving knife should always be used except when
plugging in the middle of the workpiece.
Do not stop the saw blade by lateral pressure on the
disc.
Guide rule (Fig. 12 & 13)
The handy guide rule allows you to do extra-accurate
straight cuts. Simply slide the guide rule up snugly
against the side of the workpiece and secure it in
position with the screw on the front of the base. It also
makes repeated cuts of uniform width possible.
Joint assembly (Fig. 14 & 15 & 16)
(for connecting a vacuum cleaner)
When you wish to perform clean cutting operation,
connect a vacuum cleaner to your tool. Install the joint
on the tool using the screw. Then connect a hose of
vacuum cleaner to the joint.
MAINTENANCE
CAUTION:
Always be sure that the machine is switched off and
unplugged before carrying out any work on the
machine.
To maintain product safety and reliability, repairs,
maintenance or adjustment should be carried out by a
Makita Authorized Service Center.
5603R 5413R (E) (’99. 6. 11)
9
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 5103 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 5103 in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info