448198
6
Zoom out
Zoom in
Previous page
1/9
Next page
6
Operation (Fig. 14)
Hold the tool firmly. Set the base plate on the workpiece
to be cut without the wheel making any contact. Then
turn the tool on and wait until the wheel attains full speed.
Feed water to the wheel by adjusting the water cock to
obtain a gentle flow of water. Move the tool forward over
the workpiece surface, keeping it flat and advancing
smoothly until the cutting is completed. Keep your cutting
line straight and your speed of advance uniform.
For fine, clean cuts, cut slowly. (When cutting glass plate
5 mm thick, cut at about 250 mm/min. When cutting tile
10 mm thick, cut at about 300 mm/min.) Also slow down
as you complete a cut to avoid breaking or cracking the
workpiece being cut.
CAUTION:
Be sure to hold the workpiece firmly down on a stable
bench or table during operation.
Do not twist or force the tool in the cut, or the motor
may be overloaded or the workpiece may break.
Do not use the tool with the wheel in an upward or side-
ways position.
When cutting glass plate, it is recommended to attach a
rubber plate (optional accessory) on the base of the
tool to prevent the workpiece surface from being
scratched.
The wheel for Model 4190D/DB is a wet-type wheel for
glass and tile applications. Be sure to feed water to the
wheel during operation.
• If the cutting action of the wheel begins to diminish,
dress the cutting edge of the wheel using an old dis-
carded coarse grit bench grinder wheel or concrete
block. Dress by pressing lightly on the outer edge of the
wheel.
Cutting performance
The following reference table indicates the approximate
cutting capacity from a single battery charge.
CAUTION:
If the tool is operated continuously until the battery car-
tridge has discharged, allow the tool to rest for
15 minutes before proceeding with a fresh battery.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and the bat-
tery cartridge is removed before carrying out any work on
the tool.
After use
Brush off accumulation of dust on the base.
To maintain product safety and reliability, repairs, mainte-
nance or adjustment should be carried out by a Makita
Authorized Service Center.
Workpiece Thickness
Cutting length (90°)
4190D 4190DB
Glass
3mm 5m 8m
5mm 2m 3m
Ceramic tile
5mm 4m 6m
10 mm 3.5 m 5.5 m
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 4190 DB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 4190 DB in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info