598723

Makita 192506-3-B Manual

4
Zoom out
Zoom in
Previous page
1/16
Next page
4
ENGLISH
Explanation of general view
1 Clamp screw (B)
2 Guide rail adaptor
3 Clamp screw (A)
4 Slot in base
5Base
6 Pointer
7 Graduations
8Guide rail
9 Align with cutting line
10 Workpiece
11 Protrusion of guide rail
12 Groove in guide rail adaptor
13 Clamp screw
14 Stopper
15 Stopper position for 0° bevel cut
16 Stopper position for 45° bevel
cut
17 Align with cutting line
18 Push plate
Use this Guide Rail Adaptor with MAKITA or FESTO Guide Rail.
CAUTION:
Always be sure that the circular saw is switched off and unplugged before installing or removing the guide rail adaptor.
For 5603R, 5703R and 5705R
Installation (Fig. 2)
Insert the guide rail adaptor into the slots in the base until the guide rail adaptor comes in contact with the edge of the
base. Tighten the clamp screws (A) to secure the guide rail adaptor.
How to use
1. Loosen the clamp screws (B). Adjust the guide rail adaptor so that the pointer will point to the graduation corre-
sponding to your desired bevel cut angle (0°, 15°, 30° or 45°). Tighten the clamp screws (B) to secure the guide rail
adaptor. (Fig. 3)
2. Align the edge of the guide rail with the cutting line on the workpiece. (Fig. 4)
3. Place the circular saw on the guide rail so that the groove in the guide rail adaptor with fit onto the protrusion of the
guide rail. (Fig. 4)
4. Now you can start cutting.
For 5903R and 5103R
Installation
1) For 0° or 45° bevel cuts
1. Set the stoppers on the guide rail adaptor to the 0° or 45° bevel cut position. (Fig. 6 & 7)
2. Place the circular saw on the guide rail adaptor so that the edge of the base will contact the stoppers on the
front and back. Tighten the clamp screw to secure the guide rail adaptor. (Fig. 8)
Note:
Make sure that the front surface of the push plate is flush with the side of base as shown in the figure. (Fig. 10)
2) For 15° or 30° bevel cuts
1. Set the stoppers on the guide rail adaptor to the 0° bevel cut position. (Fig. 6)
2. Place the circular saw on the guide rail adaptor and align the edge of the base with the desired graduation on
the guide rail adaptor. Tighten the clamp screw to secure the guide rail adaptor. (Fig. 9)
Note:
Make sure that the front surface of the push plate is flush with the side of base as shown in the figure. (Fig. 10)
How to use (Fig. 11)
1. Align the edge of the guide rail with the cutting line on the workpiece.
2. Place the circular saw on the guide rail so that the groove in the guide rail adaptor will fit onto the protrusion of the
guide rail.
3. Now you can start cutting.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 192506-3-B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 192506-3-B in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info