494208
32
Zoom out
Zoom in
Previous page
1/37
Next page
English
32
8  Useful tips
FAQ
Question Answer
My remote control does not 
work.
What should I do?
Check the antenna or cable connection to the main unit.
Check the batteries of the remote control.
Check if there is an obstacle between the infrared sensor window and the remote control.
Test the signal Output use IR Signal Check.
p.34
If okay, then possible infrared sensor trouble.
Aim the remote control directly at the infrared sensor window on the front of the unit.
Reduce the distance to the unit.
Re-insert the batteries with their polarities (+/– ) as indicated.
When there is an infrared-equipped device such as PC near this unit, it may interrupt the remote control signal of this unit. Move
the infrared-equipped device away from this unit, change the angle of the infrared sensor or Turn Off the infrared communication
function.
How come the Initial setup 
appears every time I Turn On 
this unit?
Connect the RF coaxial cable to the unit directly and run the initial setup.
Make sure to complete the initial setup before the unit goes into Standby mode.
Why can I not watch some RF 
signal TV programs.
Autoprogram must be completed when you set up the unit for the rst time or move it to a location where previously unavailable
channels are broadcast.
Make sure Autoprogram has been completed.
p.19
The selected channel may not be broadcasting.
When Autoprogram is interrupted and not completed, some channels will not be received. Make sure to complete the
Autoprogram.
p.19
The selected channel cannot be viewed by the Child and ratings lock setting.
p.22
The unit requires some kind of antenna Input. An indoor antenna (Digital or VHF / UHF), an external antenna (Digital or VHF / UHF)
or an RF coaxial cable from your wall cable/satellite box needs to be plugged into the unit.
How come there is no image 
from the connected external 
devices?
Check if the correct Input mode is selected by pressing SOURCE or using CH + / . Refer to Watching channels from an external 
device.
p.14
Check the antenna, cable or other Input connection to the unit.
When using the Component Video connection check that the Green (Y), Blue (Pb/Cb) and Red (Pr/Cr) connectors are connected
to their corresponding colored jacks on the unit.
When I enter a channel number,
it changes automatically.
Many Digital channels have alternate channel numbers. The unit changes the numbers automatically to the ones signifying the
broadcasting station channel number. These basic numbers used for previous Analog broadcasts. (e.g., Input ch# 30 automatically
changes to ch# 6.1)
Why are captions not displayed 
entirely? Or, captions are 
delayed behind the dialog.
Captions that are delayed a few seconds behind the actual dialog are common for live broadcasts. Most captioning production
companies can display a dialog to maximum of 220 words per minute. If a dialog exceeds that rate, selective editing is used to
insure that the captions remain up-to date with the current TV screen dialog.
How can I set the clock ? There is no clock function on this unit.
I cannot change the Child lock 
setting because my PIN code no 
longer works.
If a Power failure occurs for longer than 10 seconds the child lock setting is retained, but the PIN code is reset to the default code
0000. Refer to Child and ratings lock.
p.22
Troubleshooting
If the unit does not perform properly when operated as instructed in this Owner’s Manual,
check the following chart and all connections once before calling for service.
Symptom Remedy
No power Make sure the AC power cord is plugged in.
Make sure that the AC outlet supplies the proper voltage, plug another electrical appliance into the AC outlet to ensure that the AC
outlet operates normally.
If a power failure occurs, unplug the AC power cord for 1 minute to allow the unit to reset itself.
Control buttons do not work. Press only one button at a time. Do NOT press more than one button at the same time.
Ensure that no buttons on the remote control are depressed and move freely.
Continued on next page.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Magnavox 22ME402V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Magnavox 22ME402V in the language / languages: English as an attachment in your email.

The manual is 7,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info