Manual Magnat QUANTUM 803 (page 6 of 36) (English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish)

581677

Zoom out

Zoom in

1/36

Dear MAGNAT Customer,

Congratulationson yourfinenew loudspeakersandthankyouvery muchforchoosing MAGNAT!Youhave madeanexcellentchoice.The

high-quality speakers producedby MAGNATare renowned allover the world.

Please study theinstructions and informationbelow carefully before using yournew loudspeakers.

GENERAL INFORMATION ABOUT CONNECTING YOUR MAGNAT QUANTUM 800 LOUDSPEAKERS

Warning

: Only hi-fi amplifier loudspeaker outputs may be connected to the Quantum 800 loudspeaker terminal.

Please always use a good quality loudspeaker connection cable from an audio dealer. To prevent impairment of sound quality, we

recommend cables withcross-sections of atleast 2.5 mm² for lengthsup to 3m and at least 4mm² for lengthsabove 3 m.

Always turn off the amplifier or receiver before connecting ordisconnecting loudspeaker cables. Place the loudspeakers in their planned

positions and cutthe cables tothe right length. Thecables for both channels shouldalways be exactlythe same length.

For good sound it is imperative that the cables must be connected in such a way that the speakers are “in phase”. This means that the

black negative terminalson the speakers (-)must be connectedto the negative (-)terminals on theamplifier,the redpositive (+) speaker

terminals to the positive (+) amplifier terminals. To make this easier one wire of most speaker cables is marked with a coloured strip or a

ridge in theinsulation.

The Quantum 800terminal is designedfor 3 cord sets:

Connection via bananaplugs (fig. 1a)

Connection via clevistype fittings (fig.1b)

Non-ready-made (fig. 1c):

Strip 10– 15 mmof insulation fromthe ends ofnon-ready-made cables.Twistthe ends– thisis much betterthan tinning themwith solder

– insert themin the terminalsand tighten the terminal screwsfirmly.

Before switchingon the systemdouble-check all your connectionsand makesure thatthe terminal screwsare tight and thatthere areno

short circuitscaused by straywire filaments – thiscould cause seriousdamage to your amplifier!

THE MAGNAT QUANTUM 800 LOUDSPEAKERS IN STEREO MODE

In the ideal configurationthe speakers and thelistening position should forman equilateral triangle. Whenthe left andright speakers are

the same distance from the listeningposition their soundarrives at the sametime, resulting in a harmonious,natural music reproduction.

(Fig. 2)

There should be a clear line of sightbetween the loudspeakers and the listening position.Any sound-absorbing or reflecting obstacles in

the pathwill distort thesound. When you installthe loudspeakers thefollowing distancesshould be maintained:

Quantum tower loudspeakers: atleast 20cm awayfrom therear walland atleast 30cm fromthe sidewalls.This willprevent excessive

emphasis of thebass range.

Quantum shelf-top loudspeakers: shelfloudspeakers should alsobe asfree-standingas possible,the distance to thesides and rearto

walls and itemsshould be atleast 10 cm, the tweetersshould be locatedat earheight.

MAGNAT QUANTUM 800 LOUDSPEAKERS AS A FRONT OR REAR LOUDSPEAKER

Thefrontloudspeakersarepositionedatearheightontheleftandrightasequidistantfromthetelevisionaspossible.Therearloudspeakers

are placed atear height ora little above on theleft andright besides or better behindthe listening position.

therwise all therecommendations made inthe previous chapter also apply.

ASSEMBLING THE SUPPLIED METAL SPIKES (QUANTUM 807, 805) (FIG. 3)

All ofthe speakersin theQuantum 800series areequipped withhigh-quality aluminiumfeet which ensurea securefooting in themajority

ofsituations.Thesuppliedmetalspikes,however,aremoreappropriateforsomefloorcoverings(e.g.carpets,unevenfloors,etc.).Athread

is incorporated inthe middle ofthe aluminium feet, into whichthe spikes canbe screwed.

Adjusttheheightoftheindividualspikessothatthespeakerstandsstraightandrigid(allfourspikesmusthavefirmcontactwiththeground).

The supplied socket wrench (wrench size 10) makes it easier to screw in the spikes. You can then tighten the locknut for the spikes by

using the othersocket wrench (wrenchsize 13).

MAGNAT QUANTUM 800 - BI-WIRING AND BI-AMPING

Bi-wiring means using separate cables to carry the high and low audio frequencies. Bi-amping takes this idea one step further and uses

separate power amplifiers as well as separate cables for high and low frequencies. Bi-amping in particular produces an additional

improvement in soundreproduction quality.

The special connection terminalsof the Quantum 800loudspeakers support both conventionalconnection and operation inbi-wiring and

bi-amping modes. There are four screw terminals on each speaker. The top pair are for the tweeter (high frequencies), the lower pair for

thewoofer (lowfrequencies).The factory-installed cablesstripsconnecting thepositiveand negativeterminalsareforconventional 2-wire

connection and must be removed for bi-wiring and bi-amping operation. The pictures below show the correct set-up for conventional

operation (fig. 4a),bi-wiring (fig. 4b)and bi-amping (fig. 4c).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Magnat QUANTUM 803 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 1,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Magnat QUANTUM 803 Manual

Product: