587002
51
Zoom out
Zoom in
Previous page
1/55
Next page
51
is compatible with the LT-TB. If pressing Power and Trim does not cause any LEDs to
flash, causes a sequence lower than 28 to flash, or causes a single number to flash, then
your unit needs to be updated.
7. Check that the LT-TB is connected via a Thunderbolt cable (not provided).
8. Check that the OS is compatible with the LT-TB. One must be running OS X 10.8.5+ or
Windows 7 OR 8 (32-bit or 64-bit).
9. Remove all other Thunderbolt devices from the bus and retry.
10. Close the Lynx Mixer and any audio applications and reset the LT-TB either by removing
then reinserting the cable, or by turning the Aurora off for 5 seconds, then turning it back
on.
Continuous clicking, popping or crackling noises in your audio:
1. Check clock master settings. In any digital audio configuration, there can be one, and
only one master clock. All other digital audio devices must be configured as slaves to the
designated master clock. Since the Aurora’s SynchroLock technology provides an
extremely stable and jitter-resistant clock, we recommend setting the Aurora as the
master clock in your digital audio system. With multiple Auroras in a system, only one
can be on Internal, the rest should be clock slaves (External).
2. Check buffer settings in your audio application software. Smaller buffer sizes are
preferred because they reduce latency (the time it takes for an audio signal to travel
through your audio software). In some cases, however, setting too small a buffer size can
overtax your computer’s processor, particularly when running multiple tracks and/or a
number of DSP plug-ins. This can result in clicks and pops and other distortion in your
audio playback. Try increasing the buffer size from within the audio application or via
the LT-TB control panel and see if your playback performance improves.
3. If other Thunderbolt devices are connected on the same bus as the LT-TB, try
disconnecting them and see if your performance improves.
4. Disable Wi-Fi, Bluetooth, or other background devices that maybe be draining the CPU
performance.
Windows does not see Thunderbolt Device:
When the Aurora-TB is first connected to a Windows computer, a dialog box will prompt
that new Thunderbolt Devices have been connected, and an application must be run to mount
the devices. The next window will have a drop down menu with the following options: Do
Not Connect, Connect Only Once, or Always Connect. It is important to choose “Always
Connect” or else the device will not appear on subsequent boot up.
Using a bus powered hard drive and it is not appearing to the operating system.
The Aurora-TB WILL support bus-powered Thunderbolt devices in a daisy chain, but it
requires connecting the LYN-TBPS1000 AC Adapter to the 12 VDC power port on the LT-
TB card. The LYN-TBPS1000 can be purchased from a Lynx dealer or the lynxstudio.com
website.
The Sample rate on the Aurora front panel does not match the sample rate of the audio
material being played:
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lynx Aurora LT-TB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lynx Aurora LT-TB in the language / languages: English as an attachment in your email.

The manual is 0,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info