599332
14
Zoom out
Zoom in
Previous page
1/14
Next page
V
PAPER
LOADING
CAUTION
High
voltage
is
present
in the
electronic section
when
the unit is
turned on.
1. TURN THE
UNIT OFF.
2. Release both
catches on the
top
of the
case. Pull out and
down on the
top
of the case
front to
expose
the
platen
as-
sembly: (See
Figure 25.)
3. Move the
stylus
belt
DOWN,
(on
the
right
side of the view-
ing area),
to
position
the
marking stylus
on
the back
side of the
platen.
NEVER
move the belt
up
the
stylus
may
be
damaged. (see
Figure
26)
SPECIAL NOTE: The
stylus
may
be
damaged
if the
platen
as-
sembly
is
pulled
down
unless the
stylus
has been moved to the
back side of
the
platen.
4. Pull out
and down on the
tab
at the
top,
center of the
platen
assembly
to
expose
the
paper
spools. (See
Figure 27.)
:
To remove
the full
take-up roll,
push
in
and rotate the left
paper
retainer
knob until it
snaps
out.
(See
Figure 28.)
The roll can now
be
easily
removed from the
paper spool
end
caps. (See Figure
29.)
6. Remove the
empty supply
core from the
right
side in the
same manner
Align
the two
notches in the core wEth the
tabs on the lower
take-up
spool.
(See Fig. 30)
Push
the
paper
retainer knob in
and ro-
tate
it
until it locks into
place.
7.
Put a fresh roll of
paper
in
position
on the
centering
posts
of the
paper spool
end
caps
on the
supply
side
(right)
of the
platen assembly.
The
paper
must
spool
oft
the bot-
tom of the roll.
(See
Figure
31.)
8.
Draw the end of the
paper
across the face of the
platen,
around the friction
roller,
over
the
take-up
core,
and
tape
it
squarely
to the
take-up
core.
(See Figure 32.) (Hint:
small
strips
of
tape may
be stored
inside
housing.)
9. Hold the
take-up spool,
and
turn the
supply
spool
clock-
wise to
put
a small amount of
tension
on the
paper
It should
be
snug
against
the
platen.
(See Figure
33.)
10. Push the
platen
assembly
back to its
operating position.
Be sure it
engages
the catch
inside the
top
of
the case.
(See Figure 34.)
11. Close the front of
the case.
Latch both catches on
the
top
of the case.
(See Figure
35.)
12. Turn the unit on. Move
the
Chart
Speed
knob
fully
clockwise. Watch the
paper
long enough
to be sure it
is
movind smoothly
and
evenly
across the
platen.
If the
paper
flutters or
begins
to run
"up-
hill", repeat
Step
8.
12
13
Figure
27
PDF compression, OCR, web-optimization with CVISION's PdfCompressor
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lowrance X-15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lowrance X-15 in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info