593894
1
Zoom out
Zoom in
Previous page
1/2
Next page
NREY922C
10-2010
CAL. Y922, YK30 , YK31, YK32 , YK33, YK34
CAL. Z001, Z002 , Z003 (R23 SERIES )
DISPLAY AND BUTTON OPERATION
CHARACTERISTICS
1. Time/calendar display: Hour, minute,
second, date, day of the week and month.
2. Automatic calendar adjustment: Calendar
adjusts automatically for odd and even
months except February of leap years.
3. Time indication: Changeover between 12-
hour and 24-hour indications is possible.
4. Stopwatch: 24-hour stopwatch with 1/100
second readout up to 40 minutes and with 1
second readout after the first 40 minutes.
Split time measurement is available.
5. Alarm: The alarm rings at the designated
hour and minute with “beep, beep” for 30
seconds.
6. Hourly time signal: Can be set to ring every
hour on the hour with a single “beep”.
7. Illuminating light (for Cal. YK30, YK31,
YK32, YK33, YK34 & Z001): The light evenly
illuminates the display in the dark.
Button B:
Calendar (month, date and day) display in
the time/calendar display.
Start/stop in the stopwatch function.
Selection of the digits to be adjusted in the
alarm setting function and the time/
calendar setting function.
Button C:
Alarm display in the time/calendar display.
Split/Split release/Reset in the stopwatch
function.
Setting the digits in the alarm setting function
and the time/calendar setting function.
Stopping the alarm in any display.
Button B while keeping Button C pressed:
Engagement and disengagement of the alarm
and the hourly time signal.
Button C while keeping Button B pressed:
Changeover of the calendar (month and date)
display.
Buttons B & C:
Alarm test in the time/calendar display.
HOW TO SET THE DUAL CALENDAR
DISPLAY
1 Press Button B to show the calendar (month,
date, and day) display. The calendar display
is shown while Button B is kept pressed.
2 The month and the date change places with
each other with each press of Button C while
keeping Button B pressed.
* In the 12-hour indication, “A” (AM)/“P” (PM)
mark is displayed. In the 24-hour indication,
there is no indication.
HOW TO USE THE STOPWATCH
1 Press Button A to show the stopwatch display.
(The stopwatch indicator starts flashing.)
The stopwatch can measure up to 24 hours
and is displayed in minutes,
seconds, and
1/100 seconds up to 40 minutes, and in
hours,
minutes, and seconds after the first
40 minutes. (The 1/100 second indicator
flashes during the first 40 minutes.)
When the measurement is over 24 hours, the
stopwatch will be reset to “0:00oo” and start
counting again.
2 Reset the digits to “0:00oo” before using the
stopwatch. When the split and the
stopwatch indicators are flashing, press
Button B to check that the stop indicator
starts flashing, and then press Button C twice
to reset the digits to zero.
3 When measuring a long period of time, return
the stopwatch to the time/calendar display
after the stopwatch starts to prevent any
possible mistaken operation.
* When Button B or C is pressed in the
stopwatch display, a single “beep” sounds
to confirm the operation.
Start Stop Restart
Stop
Reset
HOW TO SET THE ALARM
Hour setting
Minute setting
1 Press Button A for 2 seconds to activate the
alarm setting function. (The alarm set
indicator starts flashing.)
2 Press Button B to activate the “Hour” or
“Minute” setting. The display changes in the
following order with each press of Button B.
3 One digit (flashing) is advanced with each
press of Button C. The digits are advanced
quickly by keeping Button C pressed.
4 After all the adjustments are completed,
press Button A to return to the time/calendar
display.
(The display returns directly to the time/
calendar display and not to the time/
calendar setting.)
C
CB
C
B
Start
Finish time
of 1st
competitor
Stop
Finish time
of 2nd
competitor
Reset
Measurement between two competitors
Finish (First runner)
Finish (Second runner)
Note: When setting the hour digits, be sure to
check that the “A” (AM)/“P” (PM) mark is
correctly set.
[Cal. YK32 / Z001]
Hour
Minute
A
EL button
Hourly time
signal mark
Alarm mark
Day indicator
Second
EL button
C
B
[Cal. YK33]
[Cal. YK30 / YK31]
Hour
A
EL button
Hourly time
signal mark
AM/PM indicator
12-hour/24-hour indication
EL button
Alarm mark
Day indicator
Second
C
B
Minute
B
Alarm/
Hourly time signal mark
Hour
A
Second
C
Minute
Day indicator
[Cal. YK34]
Hour
Second
Minute
EL button
A
C
B
A
Minute
B
Hour
[Cal. Y922 / Z002 / Z003]
Hourly time
signal mark
Day indicator
Alarm mark
C
Second
Button A:
Selection of the display.
The selection is made in the following order:
Day
indicator
Alarm/Hourly time
signal mark
AM/PM indicator
A
A
Time/calendar display Stopwatch display
Press
Button A
for 2 sec.
A
A
Alarm settingTime/calendar setting
B
C
Month
Day
B
C
Date
Day
Month
Date
A
Stopwatch
indicator
Stop indicator
Split indicator
1/100 second
indicator
B:Start/Stop
C: Split/
Split release/
Reset
Minute
Second
1/100 second
A
C
Alarm set indicator
B
Hour
Minute
“A” (AM)
Start
Measurement and release of split time can be
repeated by pressing button C.
Split time measurement
B B CC C
Split
Split
Release
Stop Reset
Restart and stop of stopwatch can be repeated
by pressing button B.
Accumulated elapsed time measurement
B B B
BC
B
BLUE 10.8.18, 5:19 PMPage 1 Adobe
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lorus Z002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lorus Z002 in the language / languages: English as an attachment in your email.

The manual is 0,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Lorus Z002

Lorus Z002 User Manual - German - 2 pages

Lorus Z002 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info