593861
1
Zoom out
Zoom in
Previous page
1/3
Next page
CHARACTERISTICS
1. Time/calendar display:
Hour, minutes, seconds, month, date and day
of the week.
Fully automatic calendar: Calendar ad-
justs automatically for odd and even months
including February of leap years from the
year 1994 up to the end of 2043.
Time indication: Changeover between 12-
and 24-hour indications is possible.
2. Stopwatch: Measures up to 10 hours with
1100-second readout.
8 lap memory: Up to 8 lap times can be
stored in memory.
3. Stroke function:
The stroke per minute, for example pulse
rate, can be calculated and displayed.
4. Countdown timer:
Preset timer: Nine different lengths of time
(3, 5, 10, 15, 20, 30, 35, 40 and 45 minutes)
have been preset for the timer.
Adjustable timer: Up to 9 hours and 59
minutes can be set in minutes.
Auto repeat function: After the set time is
up, the timer counts down the set time again
as many times as necessary.
5. Daily alarm: The alarm can be set to ring on
a 24-hour basis. At a designated time, the dis-
play is illuminated as the alarm rings.
Hourly time signal: Can be set to ring
every hour on the hour with a single beep.
6. Illuminating light: The light evenly illumi-
nates the display in the dark.
BUTTONS AND DISPLAYS
A
C
D
“A”(AM)/
“P”(PM)
mark
Display marks
Hourly time
signal mark
Seconds
Day
E
Alarm mark
Minutes
Hour
[Cal. W620]
Month
Date
Graphic display
A
C
D
“A”(AM)/
“P”(PM)
mark
Display marks
Hourly time
signal mark
Seconds
Day
E
Alarm mark
Minutes
Hour
[Cal. W240]
Month
Date
B
B
The selection of the display can be made in the
following order with each depression of button
“A”.
Time/calendar
display
Stopwatch
display
Stroke
display
A
A
Timer
display
Alarm display
A
AA
* If the stopwatch is not reset to “00” and button
“A” is depressed to change the mode from the
stopwatch, the timer display will appear, skipping
the stroke display.
* When the display is changed by depressing button
“A”, a confirmation sound beeps.
* A flashing display mark indicates that the corresponding
function is in use.
HOW TO SET THE TIME/CALENDAR
A
C
D
“A”(AM)/
“P”(PM)
mark
Display marks
Hourly time
signal mark
Seconds
Day
B
Date
Month
Minutes
Hour
1. Depress button “A” to show the time/calendar
display.
2. Depress button “B” for 2 to 3 seconds to show
the time/calendar setting display. The second
digits start flashing.
3. Selection of the digits to be adjusted (flashing)
is made in the following order by depressing
button “C”.
Seconds Minutes Date
Hour→→
12- or 24-hour
indication
Month
Year
4. Depress button “D” to set the flashing digits.
One digit is advanced with each depression of
button “D”. Digits except seconds move quickly
by keeping button “D” depressed.
5. After all the adjustments are completed, de-
press button “B” to return to the time/calen-
dar display.
Seconds setting
Depress button “D” in accordance with a time
signal. The seconds are reset to “00” and start
immediately.
When the seconds count any number from “30” to
“59” and button “D” is depressed, one minute is
added and the seconds are reset to “00”.
Notes:
1. When setting the hour digits in the 12-hour
indication, check that “A”(AM)/“P”(PM) mark
is properly set. In the 24-hour indication, there
is no indication.
2. Once the year, month and date have been set,
the day of the week is set automatically.
3. If the watch is left untouched in the time/
calendar setting display with the digits flashing,
it will automatically return to the time/calendar
display in 2 to 3 minutes.
HOW TO USE THE STOPWATCH
The stopwatch can measure up to 9 hours, 59
minutes, 59 seconds and 99 in 1100 seconds.
* Even if the stopwatch display is changed to
another while the measurement is in prog-
ress, it continues counting properly. After
the stopwatch is used, however, be sure to
reset it as the battery energy is consumed
enormously to shorten the battery life.
* While the stopwatch is measuring, the graphic
display turns on and off repeatedly.
A
BC
D
Hour
Minutes
Stopwatch
display mark
Seconds
Current
time
1/100 second
Accumulated elapsed time measurement
C
C
C
Restart
StopStart
Reset D Stop
C
** Accumulate repeatedly by depressing button
“C”.
Depress button “A” to show the stopwatch display.
Stopwatch operation
**
Lap time measurement
C
D
Lap 1 D
C
**
“Lap time” refers to an elapsed time required to
cover a given section of the whole distance.
Lap 2Start
D
StopReset
* Lap time measured and lap number remain
displayed for 10 seconds, and then the mea-
surement in progress and the current time
appear.
* After the measurement is stopped by depressing
button “C”, the current time and total time
will be displayed in the upper and lower rows,
respectively, in 10 seconds.
** Can repeat by depressing button “D”.
Notes:
1. The lap number counts up to “99”. After “99”,
the number is displayed in two digits such as
“00” for 100, “01” for 101, and so on.
2. Up to 8 lap times can be stored in memory. If
more than 8 lap times are measured, the measurements
over 8 will not be stored in memory.
Lap No.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lorus W240 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lorus W240 in the language / languages: English as an attachment in your email.

The manual is 0,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info