697406

LightPro Outdoor receiver Remote Control 167A Manual

10
Zoom out
Zoom in
Previous page
1/12
Next page
EN
ATTENTION !
• This product should be used for 12V AC/DC applications only.
• The receiver can be installed indoors and outdoors. (IP44)
• The receiver can be operated with the remote control from a maximum distance of 40 metres in an open
eld.
• A maximum of 150W can be connected in an unlimited amount of 12V applications.
• The distance between receivers should be at least 0.5m.
• Place receiver at a height of 1 meter for optimum reception.
PLACING BATTERIES IN REMOTE CONTROL (166A)
• Insert 2 AAA batteries in the remote control as indicated on page 1.
CONNECTING THE RECEIVER
• The receiver can be placed anywhere in the 12V system to serve all 12V applications behind the receiver.
• Remove the transformer plug from the power point.
• Connect the receiver cable (1) to the 12V transformer or (main) cable.
• Connect the 12V applications or (main) cable to the output connector of the receiver (4).
• Insert the transformer plug in the power point.
PROGRAMMING REMOTE CONTROL AND RECEIVERS
• Press the programming button on the receiver (2) and hold it down for 5 seconds. The red indicator light on
the receiver will start to ash (3).
• Press the group switch button (5) on the remote control where the receiver needs to be programmed. The
indicator light (3) on the receiver stops ashing. The receiver has now been programmed under the number
of this group switch button.
• Multiple receivers can be programmed under 1 group switch button. Up to 9 groups can be served inde-
pendently.
• The main switch button (6) on the remote control switches all receivers on or off at the same time.
• The indicator light ring (7) on the remote control shows whether you switch applications on or off. When
you switch a receiver on, the indicator light ring ashes once; when you switch an application off, the light
ring ashes twice.
• When you switch a receiver on, the indicator light (3) on the receiver will be on; when you switch a receiver
off, the indicator light on the receiver will go out.
• To clear the receiver settings, press the programming button on the receiver (2) and hold it down for 15
seconds. The indicator light (3) will ash for 15 seconds. Once the light goes out, all settings will have been
cleared.
The remote control and receivers should work now. If not, do the following:
• Check whether the remote control batteries have been inserted correctly.
• Replace dead batteries in remote control.
• Check / test transformer continuity
• Check plug connections. Check the cable for an open circuit.
CONDITIONS OF GUARANTEE
We guarantee the perfect condition and function of this appliance. The guarantee is valid for 5 years
beginning from the date of sale to the end user. We will rectify all faults arising from defective materials or
manufacturing. The guarantee covers repair or replacement of the defective parts, subject to our approval.
The guarantee does not apply to damage to parts which are subject to wear and tear nor damage or defects
caused by improper use or incorrect maintenance. The guarantee only applies if the purchase receipt is sent
to the dealer together with the appliance. This guarantee does not affect your statutory rights.
MANUAL AND
SAFETY INSTRUCTIONS
… 10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for LightPro Outdoor receiver Remote Control 167A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of LightPro Outdoor receiver Remote Control 167A in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info