765510
27
Zoom out
Zoom in
Previous page
1/30
Next page
27 / 30
a) Rädermontage (Abb. B1-B3)
Das Rad (1) auf die Achse schieben.
In die Öffnung der Achse einen Splint (2) einsetzen und auseinander drücken.
Die Kappe (3) aufsetzen.
a) Montage des Handgriffs (Abb. B4-B5)
Den Rasenmäher aus der Verpackung ausnehmen. Im Lieferumfang sind 2 Handgriffsteile
enthalten.
Die Enden des unteren Handgriffs in entsprechende Öffnungen des Rasenmähers (siehe Abb. B1)
bis zum Anschlag schieben und mit Schrauben fixieren.
Auf den oberen Handgriff die Kabelhalterung einsetzen.
Den oberen Handgriff zum unteren Handgriff (siehe Abb. B2) mit den Stell- und
Befestigungsschrauben (5) befestigen.
c) Kabelklemmen
Das Anschlusskabel zwischen dem Schalter und Motor am Haltebügel mit den Kabelklemmen
befestigen, um sichere Führung des Kabels während des Betriebs und bei dem Umgang mit dem
Auffangkorb zu gewährleisten.
Hinweis: Alle Schraubverbindungen überprüfen, ggf. festziehen.
4. Vorbereitung für die Inbetriebnahme
a) Netzanschluss (Abb. C)
Das Verlängerungskabel an den Stecker des Anschlusskabels (Abb. C1) anschließen und in der
Kabelhalterung (Abb. C2 und C3) fixieren.
Das andere Ende des Verlängerungskabels an geeignete Stromdose anschließen.
b) Einhängen des Grasfangkorbs (Abb. D)
Die Schutzabdeckung hoch klappen und den Grasfangkorb in die Scharniere einhängen (Abb. D).
c) Einstellung der Schnitthöhe (Abb. E)
Die Schnitthöhe wird durch die Höhenverstellung der Vorder- und Hinterachse in eine der drei
Positionen (Schnitthöhen) eingestellt.
Den Rasenmäher auf den Kopf stellen.
Die Achse aus der Lagerung auf beiden Seiten des Rasenmähergehäuses hinausschieben, in die
gewünschte Nut verschieben und loslassen (Abb. E1).
Warnung! Vor einer Verstellung der Schnitthöhe den Rasenmäher vom Netzteil (Netz) trennen und
darauf achten, dass das Messer vollständig zum Stillstand kommt.
Wichtig: Auf die gleiche Einstellposition beider Achsenenden achten. Auch auf gleiche Höhe der
beiden Achsen (Abb. E2) achten.
5. Ein- und Ausschalten (Abb. F)
a) Einschalten
Den Sicherheitsstelltaster (1, Abb. F1) drücken und gedrückt halten.
Den Schalterhebel ON/OFF (2, Abb. F2) in Richtung zum Handgriff ziehen.
Den Sicherheitsstelltaster loslassen.
b) Ausschalten
Den Schalterhebel (2) lösen (loslassen).
Warnung: Nie versuchen den Schalter in der Stellung „EIN“ zu fixieren.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Levita LM 32K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Levita LM 32K in the language / languages: English, German as an attachment in your email.

The manual is 1,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info