646805
58
Zoom out
Zoom in
Previous page
1/60
Next page
РУССКИЙ58
SuperCross-Laser SCL 3
Проверка вертикальной линии: Поставьте прибор на расстоянии около 5 м от стены. С
помощью шнура закрепите на стене отвес длиной 2,5м. С помощью кнопок V1 и V2
отрегулируйте лазер, совместив его луч с линией отвеса. Отклонение между лазером и
шнуром отвеса по вертикали не должно превышать ±1,5 мм.
Проверка горизонтальной линии: Поставьте прибор на расстоянии около 5 м от стены и
включите перекрёстный лазер. Сделайте отметку В на стене. Поворачивайте прибор, пока
лазерный крест не сдвинется на 2,5 м вправо. Сделайте отметку С.
Расстояние между горизонтальными линиями, проведенными через
эти две точки, не должно превышать ± 2 мм. Повторите замеры,
поворачивая прибор влево.
Проверка калибровки:
3. Поставьте прибор как можно ближе к
стене на высоте точки A1. Отрегулируйте
прибор.
4. Поверните прибор на 180° и нанесите
точку A3. Разница между точками A2 и
A3 является допустимым отклонением.
Подготовка к проверке калибровки:
Вы можете проверить калибровку лазера. Для этого поместите прибор ровно посередине между
2 стенами, расстояние между которыми должно быть не менее 5 м. Включите прибор,
освободив для этого фиксатор для транспортировки (лазерный крест включен). Наилучшие
результаты калибровки можно получить,
если прибор установлен на штатив.
1. Нанесите на стене точку A1.
2. Поверните прибор на 180° и нанесите
точку A2. Теперь у вас есть
горизонтальная линия между точками
A1 и A2.
A1
A2
2.
1.
Примечание:
если расстояние между точками A2 и A3 больше, чем 5 мм на 10 м, то устройство
необходимо откалибровать. В этом случае Вам необходимо связаться с авторизованным
дилером или сервисным отделом UMAREXLASERLINER.
A3
A2
A3
A2
A2
A1
4.
3.
<
5 mm / 10 m = OK
B
C
2,5 m
< 2 mm = OK
Anleit_SCL-3_Rev.0409_A:Layout 1 16.04.2009 16:07 Seite 58
58


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Laserliner SuperCross-Laser SCL 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Laserliner SuperCross-Laser SCL 3 in the language / languages: All languages as an attachment in your email.

The manual is 1,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info