646114
5
Zoom out
Zoom in
Previous page
1/136
Next page
DE
05
LAN CableChecker
3
4
Bei dieser Anwendung wird nur der Sender benötigt. Die
Kabelklemmen mit dem RJ 11 Anschluss verbinden, die Kabel-
klemmen an das Messobjekt anschließen und das Gerät in den
TEST-Modus schalten. Wenn eine oder mehrere Dioden 1 bis 8
gleichmäßig blinken ist der Testkreis geschlossen. Wenn keine
dieser Dioden blinkt ist der Messkreis unterbrochen. Siehe hierzu
auch Tipp 1.
Durchgangsprüfung
Leitungen verfolgen
Keine Messung in der Nähe von bzw. direkt an spannungs- bzw. signalführenden
Kabeln durchführen! Es besteht die Gefahr lebensgefährlicher Stromschläge sowie
die Beschädigung des Gerätes.
!
RJ 11
rotschwarz
Dioden 1...8 blinken
abwechselnd
Dioden 1...8 blinken
nicht
RJ 11
!
a
Die Kabelklemmen mit dem RJ 11 Anschluss des Senders verbinden, die Kabelklemmen an
die gewünschte Leitung anschließen und den Sender in den SCAN-Modus schalten. An-
schließend mit dem Empfänger bei gedrückter Testmodus-Taste (15) die Leitung suchen,
siehe Bild a. Das Signal beim Empfänger auf höchste Lautstärke einstellen (14), um die
maximale Messtiefe zu erzielen.
Tipp 2: Je nach Anwendung kann es sinnvoll sein die Signalart umzustellen. Dazu im
SCAN-Modus die Taste (7) drücken. Grünes Blinken der Status-Anzeige (6) zeigt das
modulierte Signal, rotes Blinken das konstante Signal an.
– Den Messkreis spannungsfrei schalten.
– Abschirmungen im Kabel und im Umgebungsbereich (Metallabdeckungen,
Metallständerwerk etc.) verringern die Ortungstiefe des Empfängers.
Manual_LAN-CableChecker_Rev.1010_DE.indd 05 25.10.2010 14:39:01 Uhr
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Laserliner LanCable Checker at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Laserliner LanCable Checker in the language / languages: All languages as an attachment in your email.

The manual is 2,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info