646122

Laserliner DigiLevel Pro 30 Manual

5
Zoom out
Zoom in
Previous page
1/19
Next page
DigiLevel Pro 30/60/120
GB
08
GB
09
Keypad
1. (REF) – Angle reference value setting
2. ( ) – ON / OFF switch
3. (
)
)
) ) – Acoustic signal on/off
4. (MR) – Memory retrieval
5. (UNIT) – Unit of measurement selection
(° degrees / % / IN/FT)
6. (M) – MEMORY function
Display
7. Slope direction
8. Slope angle
9. Current memory position (M1 – M9)
10. Battery charge
DigiLevel Pro 30/60/120
11. Vertical vial
12. Horizontal vial
13. Magnets
14. Measuring surface, 30 / 60 / 120 cm
15. Point laser ON / OFF
16. Tripod threads, 1/4"
Rear
17 . Battery compartment
1
Inserting batteries:
Open the battery compartment (17) on the rear of the DigiLevel and
insert two new batteries (type AAA/LR03) in the manner indicated
by the installation symbols. Ensure correct polarity. The symbol (10)
indicates the level of battery charge.
Digital electronic spirit level with vertical and horizontal angle display and
point laser (650 nm).The slope can be indicated in degrees, IN/FT or percent
on the display.An acoustic signal indicates the horizontal or vertical position.
The slope memory enables angles to be projected elsewhere, while
the separate measurement memory allows up to 9 measurements results
to be stored and retrieved. Milled measuring surfaces, powerful fi xing
magnets, as well as additional vertical and horizontal vial, illuminated display.
Calibration function for increased accuracy and adaptation to measuring
surface.
Switching on and measuring:
The DigiLevel Pro can measure angles continuously to 360°.
• Switch the DigiLevel Pro on using the on/off switch (2).
• The current operating temperature in °C is shown for a few seconds.
• The slope angle is shown in the display (8). If slopes are measured
overhead, the direction of display adjusts automatically.
• The current slope direction is also shown by the symbol (7).
Selection of unit of measurement:
• Button (5) allows the desired unit of measurement to be selected
(° degrees, %, IN/FT)
Changing the angle reference value:
• With button (1), it is possible to transfer angles elsewhere. To do so,
set the device to the desired slope and press button (1). The display will
then change to “0.0”, and the desired reference angle is now set.
The slope can now be transferred to other objects.
IMPORTANT: When all the slopes have been transferred, make sure
to deactivate the new angle reference value. To do this, switch off
the device by pressing the on/off switch (2) for at least 3 secs. Only
then will the value be reset itself to the measuring surface (14).
Acoustic signal:
• The acoustic signal can be switched on or off with button (3).
• When the angle of slope stands at 0°, 45°, 90° or the most recently
stored value, this is indicated by an acoustic signal.
NOTE: When working with a changed angle reference value, the
acoustic signal is activated on reaching the new reference value
(0°, 45°, 90° display).
2
3
5
6
4
11
12
13
14
15
17
16
97108
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Laserliner DigiLevel Pro 30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Laserliner DigiLevel Pro 30 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 0,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info