362235
6
Zoom out
Zoom in
Previous page
1/16
Next page
12
Place a receptacle under the steam nozzle. Run 300 ml of water by pressing the rinse button once for more than 3
seconds. You can repeat this operation if you wish.
Settings
Connect the appliance to the mains power supply but do not turn it on.
Lift the cup grid by pressing on the back to make it tilt.
Press the and
- Fig. 5
.
The digital display for parameter setting is under the servicing ap
- Fig. 6
.
Look down vertically to the bottom of the window
- Fig. 7
.
Setting water hardness
The “water tank” light will come on.
Press the key
- Fig. 8
as many times as are needed to select the hardness level for the water used : 0 = very soft, 1 =
soft, 2 = moderately hard, 3 = hard, 4 = very hard.
Setting the coffee temperature
Press the steam key to switch to coffee temperature setting : The ‘
CALC
’ light will come on.
Press the key
- Fig. 8
as many times as are needed to select the desired coffee temperature : 1, 2 or 3.
Setting the automatic electrical power supply cut-off (auto-off)
It is possible to turn your machine off automatically after a number of pre-programmed hours.
Press the steam key
to switch to automatic cut-off setting :The ‘
CLEAN
’ light will come on.
Press the key
- Fig. 8
as many times as are needed to select the desired duration: 1 = 1 H, 2 = 2 H, 3 = 3 H, 4 = 4 H.
Preparing the appliance
Pull out and ll the water tank
- Fig. 9
.
Put it back in place by pressing rmly and close the lid again
- Fig. 10
.
Open the coffee bean container lid. Add the coffee beans
- Fig. 11
.
Close the coffee bean container lid again.
NEVER PUT GROUND COFFEE IN THE COFFEE CONTAINER.
It is recommended that you do not use oily, caramelised or avoured coffee beans for this machine. These kinds of beans
may damage the machine.
Check that the coffee beans do not contain any foreign particles such as grit, as any damage caused by the presence of
foreign particles will negate the warranty.
Appliances are pre-set in the factory to 1 hour.
At each of these stages, you can memorise your settings by pressing the button when you have reached the setting
you want (the 4 lights ash 2 times) or carry on with the procedure. These settings will remain memorised even if the
electrical power is cut off. You can modify these settings at any time by repeating these operations.
Appliances are pre-set in the factory to 2, average temperature.
Appliances are pre-set in the factory for hardness level 4.
The Claris cartridge needs to be replaced after about every 50 litres of water or every two months at least.
Do not fill the water tank with hot water, milk or any other liquid.
If you turn on the appliance when the water
tank is not in place or not correctly lled (under the “min.” level,), the “ll water tank” light will come on and making
an espresso or a cup of coffee will be made impossible.
6


Need help? Post your question in this forum.

Forumrules
1

Forum

krups-ea-8000

Reset search

  • EA8000 stuck on automatic maintenance and then gives error code 13. Any ideas what to try? Submitted on 17-7-2021 at 01:58

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Krups ea 8000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Krups ea 8000 in the language / languages: English as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Krups ea 8000

Krups ea 8000 User Manual - English - 12 pages

Krups ea 8000 Quick start guide - English - 26 pages

Krups ea 8000 User Manual - German - 12 pages

Krups ea 8000 Quick start guide - German - 26 pages

Krups ea 8000 User Manual - Dutch - 12 pages

Krups ea 8000 Additional guide - Dutch - 4 pages

Krups ea 8000 Quick start guide - Dutch - 26 pages

Krups ea 8000 User Manual - Dutch - 18 pages

Krups ea 8000 Quick start guide - Danish - 26 pages

Krups ea 8000 User Manual - French - 12 pages

Krups ea 8000 Quick start guide - French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info