803116
1
Zoom out
Zoom in
Previous page
1/2
Next page
KRT692010 KRT692012 KRT692015 KRT692019 KRT692030EN
Copyright © 2018 VARO P a g e | 1 www.varo.com
OPERATION INSTRUCTIONS
CAUTION: Do not keep the keys in the safe.
1 OPEN THE SAFE FOR THE FIRST TIME
To open the safe for the first time, remove the small plastic cover “Z” (see diagram 1) on the
front panel, insert the key into the lock and turn it counter-clockwise, at the same time, turn the
knob counter-clockwise and open the door.
2 INSTALLING THE BATTERIES.
The safe requires 4 x size “AA”(1.5V/R06) batteries.
The batteries compartment Y (see diagram 2) is located on the back of the door. Remove the
battery cover and install the batteries into the compartment. Ensure the batteries are fitted with
the correct corresponding polarity. Once the batteries are installed, close the battery
compartment. The system will scan the status of the electronic lock system automatically. If it
is OK, the display will show ‘good’ (see diagram 1). Use of alkaline batteries is recommend.
3 PROGRAMMING THE CODE
The safe is supplied with user code (factory preset: 0000) and master code (factory preset:
8888). For your safety, after installing the batteries, you should change the codes before using
your safe.
3.1 Changing the user code
With the safe door open, press the red set button (X) (see diagram 2) inside the battery
compartment, on display show SET COdE.
Input your code combination (3-8 digits) within 15 second, press E to confirm. On display
show IN, and the user code has been changed.
3.2 Changing the master code
With the safe door open, press the red set button (X) (see diagram 2) inside the battery
compartment, on display show SET COdE.
Press E within 15 second, on display show “old-COdE”, input preset master code “8888”,
confirm by pressing E, on display show SET.
Input new master code(3-8 digits), confirm by pressing E, on display show “RE-InpuT”,
repeat input new master code confirm by pressing “E, on display show “IN”, and the new
master code has been changed
Note: Test your code according to Step 4. If it works, you can close the door.
4 USING YOUR SAFE
Input your user code or master code, confirm by pressing “E”, on display show ‘good’.
Turn the handle anti-clockwise within 4 seconds to open the door.
Note: Pressing C can delete the last code digit.
Warning:
If the code is wrong, you will hear 3 short beeps, on display show ‘Error’.
If an intruder enters wrong codes for 4 times consecutively, the buzzer will be sound for 3
minute.
5 BUZZER CONTROL
Press E and simultaneously press 3, you can control buzzer sound.
When the display shows ‘bUZZEr’, the buzzer is active and will beep when entering a code;
when the display shows ‘SILENT’, the buzzer will not beep when entering the code, but will
sound when entering the wrong code.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kreator-Varo KRT692010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kreator-Varo KRT692010 in the language / languages: English as an attachment in your email.

The manual is 0.24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kreator-Varo KRT692010

Kreator-Varo KRT692010 User Manual - German - 2 pages

Kreator-Varo KRT692010 User Manual - Dutch - 2 pages

Kreator-Varo KRT692010 User Manual - French - 2 pages

Kreator-Varo KRT692010 Additional guide - All languages - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info