533104

Konig KN-WS600 Manual

3
Zoom out
Zoom in
Previous page
1/125
Next page
3
2. Place the anemometer horizontally in your selected outdoor location. Loosen the screws on the battery
door with a small Phillips screwdriver and open the battery door. Insert 2 pieces of AA batteries according
to the polarity indicated. Close the battery door and tighten the screws.
3. Hold the “CHANNEL/SEARCH” button on the monitor for 3 seconds and the wind direction, temperature
and humidity icons will flash on the display. The monitor is now searching for all remote sensors.
4. If valid wind direction, wind speed and channel-1 temperature/humidity readings are shown on the monitor
within 10 minutes, the RF transmission is successful and the anemometer and monitor are within the
effective transmission range.
If the above readings are not shown after 10 minutes of searching, the transmission has failed.
Shorten the distance between the anemometers and monitor. Reset the anemometer by removing all
batteries from the anemometer and wait for 10 seconds before reinstalling the batteries. Repeat steps
3 and 4 until the transmission is successful.
5. Remove all batteries from the anemometer before mounting and calibration.
3. Mounting the anemometer
Important: Before mounting, make sure the monitor and anemometer are within the effective transmission
range.
Note: To mount the anemometer, you need a mast (not supplied) of about 1 – 1.25 inches (2.54 – 3.18 cm) in
diameter, and the hardware necessary to fasten it to the mounting location. If you have previously installed
such a mast (for a mounting antenna, for example), you can mount the anemometer on that mast.
(1) If necessary, mount and ground a mast as directed in the instructions provided by the mast.
(2) Place the supplied U-shaped metal plates around the mast. Insert 4 pieces of the supplied hex screws
through the holes of the U-shaped plates and the holes on the anemometer’s mounting bracket.
(The wind vane is above the wind cup and the metal bar of the anemometer is in the horizontal level).
(3) Tighten the supplied hex nut onto both ends of each screw.
4. Calibrating the anemometer and installing batteries
After mounting the anemometer, follow these steps to calibrate the wind direction so that the anemometer
properly measures the wind direction and transmits it to the monitor. Make sure the battery has been removed
from the anemometer before calibration.
Important: The same calibration (steps 1 to 5) is needed for the first setup and every battery replacement.
(1) After mounting the anemometer, loosen the screws on the battery door with a small screwdriver and
open the battery door.
(2) Use the compass on the anemometer and turn the wind vane so it is pointing due north.
(3) Hold the wind vane pointing due north and do not allow it to turn. Insert 2 pieces of AA batteries
according to the polarity indicated. The red LED indicator above the battery cover of the anemometer
MAST
NORTH
MAST
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Konig KN-WS600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Konig KN-WS600 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info