603839
1
Zoom out
Zoom in
Previous page
1/2
Next page
*9000858095* 9000858095 921205
de
Ø
Montageanleitung
Arbeitsplattenausschnitt mit 500mm Tiefe
Bei Installation in einen bestehenden Ausschnitt (Ersatzbedarf)
mit einer Ausschnitttiefe von 500mm muss auf folgende Punkte
geachtet werden:
Ausschnitttiefe maximal 502mm.
Die Arbeitsplatte muss eben und sauber sein.
Zentrieren Sie die Mulde genau.
Die Dreiecksmarkierung muss genau mit dem angezeichneten
Strich übereinstimmen.
Beachten Sie die Hinweise in Gebrauchs- und Montageanlei-
tung.
en
Ú
Ins tallation instructions
Worktop cut-out, 500 mm deep
When installing in an existing cut-out (replacement requirement)
with a cut-out depth of 500 mm, the following points must be
observed:
Maximum cut-out depth is 502 mm.
The worktop must be even and clean.
Centre the hob precisely.
The triangle markers must be exactly in line with the mark
previously drawn.
Observe the information in the instruction and installation
manuals.
fr
Þ
Not ic e de mo ntage
Découpe du plan de travail avec une profondeur
de 500mm
Lors de l'installation dans une découpe existante
(remplacement) d'une profondeur de découpe de 500mm, vous
devez faire attention aux points suivants :
Profondeur de découpe maximale 502mm.
Le plan de travail doit être plan et propre.
Centrez la table avec précision.
Le repère en triangle doit exactement coïncider avec le trait
tracé.
Respectez les consignes dans la notice d'utilisation et de
montage.
it
â
Istruzioni per il montaggio
Foro d'incasso nel piano di lavoro con profondità
di 500 mm
In caso di installazione in un foro d'incasso preesistente
(sostituzione) con profondità pari a 500 mm è necessario
prendere in considerazione i seguenti punti:
Profondità del foro d'incasso di massimo 502 mm.
Il piano di lavoro deve essere piano e pulito.
Centrare con precisione il piano di cottura.
Il contrassegno a forma di triangolo deve coincidere alla
perfezione con la tacca segnata sul piano.
Prestare attenzione alle avvertenze presenti nelle istruzioni d'uso
e di montaggio.
nl
é
Installatievoorschrift
Uitsnijding voor werkblad met een diepte van
500mm.
Bij installatie in een bestaande uitsnijding (in geval van
vervanging) met een diepte van 500mm moet op de volgende
punten worden gelet:
Diepte van de uitsnijding maximaal 502mm.
Het werkblad moet vlak en schoon zijn.
Het blad moet nauwkeurig worden gecentreerd.
De driehoekmarkering dient precies met de aangegeven lijn
overeen te komen.
Neem de aanwijzingen in de gebruiksaanwijzing en
installatiehandleiding in acht.
da
×
M onte ri ngs vejl ed ning
Udskæring i bordplade med en dybde på 500 mm
Ved installation i en eksisterende udskæring (udskiftning) med
en udskæringsdybde på 500 mm skal følgende punkter
overholdes:
Udskæringsdybde maks. 502 mm.
Bordpladen skal være plan og ren.
Centrer kogesektionen nøjagtigt.
Trekant-markeringen skal placeres helt nøjagtigt ved den
markerede streg.
Følg anvisningerne i brugs- og montagevejledningen.


1


Need help? Post your question in this forum.

Forumrules
1

Forum

koenic-kai-16250

Reset search

  • I want to know how to use the AC in a Kai vehicle or van

    Submitted on 1-1-2022 at 17:02

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Koenic KAI 16250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Koenic KAI 16250 in the language / languages: All languages as an attachment in your email.

The manual is 0,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Koenic KAI 16250

Koenic KAI 16250 User Manual - English, German, Dutch, French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info