588364

Klipsch SW-450 Manual

3
Zoom out
Zoom in
Previous page
1/10
Next page
that no bare wires from any of the connections touch any other
terminals, as this could cause a short and damage your equipment.
“LINE IN/LFE” – This input is filtered by the built-in “Low Pass”
(LP) crossover and is designed as a general purpose input for
the subwoofer. It accepts the LFE signal output of your digital
surround electronics.
“LOW PASS” (LP) Control – This control allows the user to select
the upper frequency cutoff of the subwoofer. Frequencies above
the control setting are filtered out, allowing you to blend the
subwoofer’s output with that of your main speakers. The frequency
is selectable from 40-150Hz. For sources with an LFE output
or that use an internal crossover, the lowpass filter should be
defeated by setting the control to “BYPASS”.
“VOLUME” – This control serves as an overall volume control for
the subwoofer. It is used to match the output level of the subwoofer
to the main speakers.
“PHASE” 0/180 – This control is used to acoustically match the
subwoofer’s output to your main speakers. Select the position
either 0˚ or 180˚ in which your subwoofer has more output at the
listening position.
“Power” ON/OFF– Klipsch SW subwoofers use a detachable power
cord and do not have a main power switch. To fully remove power
from the subwoofer, the power cord must be disconnected from
the unit.
Auto/On – When this switch is in the “ON” position, the subwoofer
will remain on at all times. When this switch is in the “AUTO”
position, the subwoofer will automatically turn “on” when it senses
a signal. It will automatically turn “off” after 15 minutes with no
signal. When this switch is in the “OFF” position, the subwoofer will
remain “off” until the switch is manually turned back to the “ON” or
“AUTO” position.
LED indicator– Klipsch SW subwoofers have an LED indicator
on the front that indicates the status of the built in amplifier. The
LED will light blue when the amplifier is on and receiving a signal.
When the unit is in standby mode or turned off, the LED indicator
will turn off.
Your subwoofer has a durable vinyl finish that should only require
dry dusting or cleaning with a dry cloth. Avoid the use of abrasive or
solvent-based cleaners and harsh detergents. The brush attachment
of your vacuum should remove any dust from your subwoofer
enclosure.
Care and Cleaning
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Klipsch SW-450 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Klipsch SW-450 in the language / languages: English, French as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info