Manual Klipsch RW-12d (page 3 of 30) (English, German, French, Italian, Portuguese, Spanish)

588341

Zoom out

Zoom in

1/30

CONNECTIONS AND CONTROLS

CAUTION: Turn off your amplifier and your subwoofer before

making any connections. Do not connect both the “High

Level” and “Line Level” inputs at the same time as damage

to your equipment could result.

RW-10d / RW-12d / RSW-10d

“LINE IN” -

This input is designed as the standard or default

input for the subwoofer. It accepts signals from the Left and

Right channel pre-amp, subwoofer or LFE outputs of your elec-

tronics via the RCA jack inputs. Connect to the “RIGHT” and/or

“LEFT/LFE” inputs on the subwoofer’s rear panel (Refer to

figures 3 and 5).

RW-10d / RW-12d

“HIGH LEVEL IN”

- These connections can be used as an

alternate connection method to the line level hook up. Using

16- gauge or larger speaker wire, connect the Red “positive” (+)

terminal of your amplifier’s Left channel to the Red “positive” (+)

terminal of your subwoofer’s Left channel ”HIGH LEVEL IN”

terminal. Connect the Black “negative” (-) terminal of your ampli-

fier’s Left channel to the Black “negative” (-) of your subwoofer’s

Left channel ”HIGH LEVEL IN” terminal. Repeat this procedure for

the Right channel connections (refer to Figure 4). Take care that

no bare wires from any of the connections can touch any of the

other terminals as damage to your equipment could result.

CONTROLS

All of the subwoofer’s controls, and changes to control settings,

are accessed through the cursor key pad and display on the top

of the subwoofer’s cabinet. The only exception to this is the main

AC power switch which is located on the rear panel of the

subwoofer.

• Use the (UP) or (Down) key to scroll through the list of

control options.

• Use the (Left) or (Right) Key to make adjustments to a

given control setting

• Use (IE Center Key) when the “ ” appears on the display

to store and recall custom settings or to lock the keypad

• After adjusting the individual control parameters for “Volume”,

“EQ Mode”, “Low-pass filter” and “Phase”, your settings can

be stored in one of three user memories (“Movie”, “Music”

and “Night”). This allows for global recall of all of the above

settings to tailor the subwoofer’s performance to compensate

for differing source material and uses.

• The display will return to the “Volume” screen after 10

seconds if no adjustments are made while in any other control

or display mode.

• In periods of low humidity, it is possible that a static electricity

discharge to the subwoofer may cause a momentary

interruption in the subwoofers output or changes to the LCD

display content. Any display content errors will be corrected

when the screen changes modes.

“Volume” - Use the Left/Right cursor keys to adjust the

subwoofer’s volume level to match the output of your main

speakers. The volume control on your system’s main amplifier

or pre-amplifier will be the overall volume control for your

subwoofer and full range speakers. Press and hold (or press and

release) the Left cursor key to decrease the subwoofer’s volume.

Press and hold (or press and release) the Right cursor key to

increase the subwoofer’s volume to the desired level. From

this screen press the down cursor key to access other control

settings.

“Recall Settings:” - This screen is used to select any one of

three, user defined, memory presets titled “Movie”, “Music” and

“Night”. Use the Left/Right cursor keys to select the desired

group of stored control settings and press the Center key to

apply them. “Settings Recalled!” will then be displayed. All of the

user settings, in the three memory presets, can be erased and

restored to their default values by scrolling down to the last

“System Info” screen. Press the Right cursor key twice to get to

the “System Reset” screen. Press the center cursor key and all

user settings will be replaced with the default settings. “Reset

Complete” will be displayed. During initial setup, skip this screen

until all other initial control adjustments have been made. From

this screen press the down or up cursor key to access other

control settings.

“EQ Mode:” - This screen is used to select two different Bass

emphasis settings, titled “Punch” and “Depth”. They are designed

to complement different types of program material, such as

movie soundtracks or music. The “Punch” setting emphasizes the

60Hz region while the “Depth” setting boosts the 30Hz range. A

third setting is titled “Flat” which defeats these two settings. Use

of either of these EQ settings will slightly reduce the subwoofer’s

maximum output capability as they will require more of the

subwoofer’s amplifier power. Use the Left/Right cursor keys to

select the desired EQ setting. From this screen press the down

or up cursor key to access other control settings.

“Lowpass” - This screen is used to adjust the subwoofer’s

upper frequency limit to achieve a proper blend with your

system’s main speakers. A higher frequency (Hz) is typically used

with smaller, bass limited main speakers and a lower frequency

setting is customarily used with larger floorstanding models. This

filter can be adjusted from 40Hz to 120Hz, as required, or

defeated if the low pass filter function is being performed by your

system’s electronics. Use the Left/Right cursor keys to adjust the

lowpass filter. To defeat this filter press and hold the Right cursor

key until “Lowpass OFF LFE Mode” is displayed. Refer to your

surround processor’s owner’s manual for more Bass

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Klipsch RW-12d in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Klipsch RW-12d Manual

Product: