Manual Klemko 891042 - D-PAF 200 LED (page 2 of 3) (English, German, Dutch)

742264

Zoom out

Zoom in

1/3

Introduction

Through the use of trailing edge, it is possible to dim

the connected load with this dimmer without noise.

This dimmer is equipped with a ﬁne fuse and tem-

perature fuse. If overloaded the dimmer will reset

automatically after the cooling-oﬀ period. The cause

of the overload should be reviewed and ﬁxed as soon

as possible. The dimmer is electronically protected

against short circuit and overload. In the event of a

short-circuit or a long-term overload, the fuse in the

dimmer will be permanently activated.

Waranty: 24 months if the product has been used ac-

cording to the instructions and has not been opened.

User manual for Klemko LED dimmer, trailing edge

receivers for electronic transformers.

891042 D-PAF-200-LED

These dimmers can become hot when in operation.

The consequence of because a part of the connected

load (the losses) turns into heat. The rated power

output of the dimmer only applies to installations in

a massive stone wall. If the dimmer is installed in a

wall of aerated concrete blocks, wood, plaster, or a

build-up edge, the maximum connected load must

be reduced by a min. of 20%. This is also neces-

sary when there are multiple dimmers installed in a

combination. (NEVER MAKE A VERTICAL COMBINATION

WITH MULTIPLE DIMMERS!). The same counts when

there is an extreme heat source nearby the dimmer.

Heat

Connection

• Disconnect power

• Connect according to the wiring diagram

(Note: do not switch live wire and zero)

• Secure the cover plate with the nut

• if necessary, use the shaft adapter to widen the

shaft to 6mm.

• Place the knob

Installation instructions

Voltage 230 Vac (+6 % / -10%)

Power 1 - 200 W

Max. led drivers 15 pcs

(multiple leds per driver possible)

Max. light sources 15 pcs

Dimming Trailing edge / RC

Change over relais Yes

Fuse circuit breaker 16A IEC/EN 60898 certiﬁed, Type B

Inrush current 1000 A / 20 µsec

Standards TÜV / CE

Speciﬁcations

This intelligent dimmer is equipped with a ﬁne

adjustment. If your lights ﬂash, this small button

allows you to adjust the minimum brightness.

Proceed as following:

Turn the dim shaft fully to the left. Now trim the

potentiometer with a screwdriver (see wiring di-

agram) to the desired minimum brightness.

Adjusting minimum brightness

Klemko Techniek B.V.

Nieuwegracht 26 T +31 (0)88 002 3300

NL-3763 LB Soest www.klemko.nl

the Netherlands info@klemko.nl

Driver / transformator

L L

On/Oﬀ

Minimum brightness

Turn the dim shaft fully to the left;

Now trim the potentiometer with a screwdriver

(see wiring diagram) to the desired minimum

brightness. Set the potentiometer between 5 %

and 30 %.

• (Dimmable) led-lighting

• (Retroﬁt) lightbulbs

• High volt halogen 230V

• Electronic transformers for trailing edge

Works with

A. Press the rotary knob: the connected lamps are

switched on or oﬀ.

B. Turn the rotary knob either clockwise or coun-

ter-clockwise.

The connected lamps are dimmed brighter or

darker.

Warning:

each terminal

pin connects

to one wire

only

DANGER

Risk of serious damage to property and per-

sonal injury, e.g. from ﬁre or electric shock,

due to incorrect electrical installation.

The outputs may carry an electrical current even

when the device is switched oﬀ. Always disconnect

the fuse in the incoming circuit from the supply befo-

re working on connected loads.

Safe electrical installation can only be ensured if the person in

question can prove basic knowledge in the following areas:

• Connecting to installation works

• Connecting several electric devices

• laying electric cables

These skills and experience are normally only pos-

sessed by skilled professionals who are trained in the ﬁeld of

electrical installation technology.

If these minimum requirements are not met or are disregarded

in any way, you will be solely liable for any damage to property or

personal injury.

For your safety

Installation

Install the dimmer in a single, standard ﬂush mounting box, or drill a

65,5mm diameter hole.

Changeover circuit (image. 2)

Resetting the dimmer / Preparing the dimmer for the ﬁrst time (image. 3)

Installation (image. 4)

Driver / transformator

L L

Max.

When you ﬁrst install the dimmer or with every ad-

justment or modiﬁcation of the connected lighting,

the dimmer settings can no longer be optimal.

Resetting the dimmer:

1. Turn on the light at maximum brightness

2. Turn the smart adjustment to 5%

3. Within 2 seconds turn the smart adjustment

from 5% directly to 30% and back to 5%.

The connected light will go oﬀ and on again.

The next step is to set the minimum brightness of

the connected lights.

Preparing dimmer for ﬁrst use (image. 3)

Warning: Before installation, disconnect all cables for the part of

the installation feeding the lights. Read the instructions carefully.

If in doubt, consult a certiﬁed electrical installer !!!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Klemko 891042 - D-PAF 200 LED in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 0,96 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Klemko 891042 - D-PAF 200 LED Manual

Product: