784262

KKT Kolbe CC9001IND Manual

89
Zoom out
Zoom in
Previous page
1/92
Next page
89
EN
Before connecting, check if the voltage indicated on the type plate corresponds to the mains voltage. The length of the
connection cable must be sized so that the device can be connected prior to insertion. The protective conductor must be
sized so that it is loaded onto train at the strain relief fails aer the live wires of the connection cable.
!
Electrical connection
•
This appliance must be earthed by law. Before connecting the appliance to the
electrical supply, check that the earth system in your house is working correctly.
•
Check that unit voltage and power, marked on the rating plate applied on the
appliance, are correct for the supply. It is necessary that the feeding network is
protected by a powerful switch able to disconnect completely the network with a
contacts separation of at least 3 mm. Be sure that the earth wire green/yellow is
not interrupted by the switch.
WARNING: THIS APPLIANCE MUST BE EARTHED
•
In order to avoid hazard, any electrical work performed on this equipment or its
associated wiring should only be done by persons authorised by the
manufacture or similary qualified persons.
Replacement or mounting of the power cord
The mains cable is replaced via the rear backboard.
The mains cable must be of the following type:
380
-
H05
H05
V
H05
H07
-
415V 3N~
RR-F
V
V-F 5×
2
RN-F
RN-F
2
.5mm2
220-240V
H05RR-F
H05VV-F
H05RN-F
H07RN-F
3×4mm2
EN
This appliance must be earthed by law. Before connecting
the appliance to the electrical supply, check that the earth
system in your house is working correctly.
• Check that unit voltage and power, marked on the rating
plate applied on the appliance, are correct for the supply. It
is necessary that the feeding network is protected by a pow-
erful switch able to disconnect completely the network with
a contacts separation of at least 3 mm. Be sure that the earth
wire green/yellow is not interrupted by the switch.
WARNING: THIS APPLIANCE MUST BE EARTHED
•
In order to avoid hazard, any electrical work performed on
this equipment or its associated wiring should only be done
by persons authorised by the manufacture or similary quali-
ed persons.
Replacement or mounting of the power cord
The mains cable is replaced via the rear backboard.
The mains cable must be of the following type:
Leave the mains cable slightly overlong so that you can pull out the appliance for cleaning purposes.
Proceed as follows:
• Remove the rear backboard.
• Undo the screw on the terminal block that xes the cable in place.
• Loosen the screw contacts and replace the cable with a new one of the same length.
The cable must comply with the stipulated speci- cations.
• Connect the yellow-green wire to the
terminal. This wire must be at least 10 mm
longer than the other wires.
• Connect the blue neutral wire to
terminal N.
• Connect the brown power wire to
terminal L.
Installation and connection of the appliance
Power connection
… 89 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for KKT Kolbe CC9001IND at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of KKT Kolbe CC9001IND in the language / languages: English, German as an attachment in your email.

The manual is 2.92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info