508900

Kicker IX500.4 Manual

3
Zoom out
Zoom in
Previous page
1/28
Next page
3
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
IX500.4 2 x 50 Ampere 4 Gauge PK4, CK4, ZCK4
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the
amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the
battery’s negative post and the vehicle chassis is recommended.
The IX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereo’s source unit. Ideally, when connecting the source unit to the amplifi er, the IX amplifi er’s input
level switch should be set to “LO” and a low-level signal should run from the source unit’s stereo RCA output to
the stereo RCA input on the end panel of the amplifi er using RCA interconnect cable. If a low-level stereo RCA
output is not available on the source unit, the signal can be delivered to the amplifi er using the high-level speaker
outputs on the source unit. Set the input level switch on the end panel of the amplifi er to “HI”. Crimp and solder
RCA connectors to the end of the speaker wire running from the high-level speaker outputs on the source unit
and connect the wire to the RCA Inputs on the end panel of the amplifi er or simplify the installation by using a
KICKER ZISL as shown below. Either input method will provide a low-level output signal at the RCA output, which
effectively passes the audio signal to another amplifi er or component. Keep the audio signal cable away from
factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to amplifi er
shield
+
–
core conductor
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er. Install
a second fuse within 18” (45cm) of the amplifi er. If you ever need to remove the amplifi er from the vehicle after it
has been installed, the ground wire should be the last wire disconnected from the amplifi er--just the opposite as
when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR
to amplifi er
INPUT
LEVEL
LO
HI
AMP2AMP1
L
R
OUTPUT
POWERAMP1
GNDL+ L– R+ R– REM +12V
AUTO
TURN ON
12V DC AUDIO
OFFSET
FADER
OFF
ON
BRIDGED
AMP2
L+ L– R+ R–
BRIDGED
12V
18”
(45cm)
battery
external fuse
external fuse
remote turn-on
(see page 5)
bare-metal
chassis ground
24”
(60cm)
2010 IX 500.4 RevB.indd 32010 IX 500.4 RevB.indd 3 11/12/2009 2:16:38 PM11/12/2009 2:16:38 PM
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kicker IX500.4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kicker IX500.4 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info