4
Instructions for Assembly
■ Ensure that you have received all the parts required (see check list)
and that they are undamaged. Should you have any cause for com-
plaint, please contact your KETTLER dealer.
■ Before assembling the equipment, study the drawings carefully and
carry out the operations in the order shown by the diagrams. The
correct sequence is given in capital letters.
■ The equipment must be assembled with due care by an adult person.
If in doubt call upon the help of a second person, if possible tech-
nically talented.
■ Please note that there is always a danger of injury when working
with tools or doing manual work. Therefore please be careful when
assembling this machine.
■ Ensure that your working area is free of possible sources of danger,
for example don’t leave any tools lying around. Always dispose pack-
aging material in such a way that it may not cause any danger. There
is always a risk of suffocation if children play with plastic bags!
■ The fastening material required for each assembly step is shown in
the diagram inset. Use the fastening material exactly as instructed.
The required tools are supplied with the equipment.
■ Bolt all the parts together loosely at first, and check that they have
been assembled correctly. Tighten the locknuts by hand until resis-
tance is felt, then use spanner to finally tighten nuts com-
pletely against resistance (locking device). Then check that
all screw connections have been tightened firmly. Attention: once
locknuts have been unscrewed they no longer function correctly (the
locking device is destroyed), and must be replaced.
■ To pull off the pedal arms remove cap and screw (A). Grip the pedal
arm tightly, and screw in an M12 bolt (not supplied) into the thread
(B). After a few turns you may take off the pedal arm (C).
■ For technical reasons, we reserve the right to carry out preliminary
assembly work (e.g. addition of tubing plugs).
■ Please keep original packaging of this article, so that it may be used
for transport at a later date, if necessary.
Instructions de montage
F
Pour votre sécurité
■ La bicyclette pour la mise en forme, ne doit être utilisée que pour
les fins auxquelles elle est destinée, c'est-à-dire pour l'entraînement
des adultes.
■ Tout autre emploi est interdit, voire dangereux. Le fabricant ne
pourra être rendu responsable de dommages causés par l'emploi
inadéquat de l'appareil.
■ Vous vous entraînez avec un appareil dont la technique et la sécurité
correspondent aux exigences modernes. Les sources possibles de
danger qui pourraient entraîner des blessures ont été soit sup-
primées, soit sécurisées.
■ Les réparations inadéquates et les modifications apportées à la
construction de l'appareil (démontage des pièces d'origine, montage
de pièces non autorisées, etc.) peuvent entraîner des risques imprévus
pour l'utilisateur.
Lire attentivement les présentes instructions avant le montage et la première utilisation de l'appareil. Elles contiennent des renseignements
importants relatifs à la sécurité des personnes ainsi qu'à l'emploi et à l'entretien de la bicyclette d´áppartement . Conserver soigneusement les-
dites instructions pour d'éventuels renseignements ainsi que pour effectuer l'entretien de l'appareil ou commander des pièces de rechange.
■ The machine is designed for use by adults and children should not
be allowed to play with it. Children at play behave unpredictably
and dangerous situations may occur for which the manufacturer cannot
be held liable. If, in spite of this, children are allowed to use the
equipment, ensure that they are instructed in its proper use and super-
vised accordingly.
■ The exercise cycle complies with the DIN EN 957 - 1/5, class HB.
It is therefore unsuitable for therapeutic use.
■ A slight production of noise at the bearing of the centrifugal mass is
due to the construction and has no negative effect upon operation.
Possibly occurring noise during reverse pedalling result from
engineering and are absolutely safe.
■ Do not use corrosive or abrasive materials to clean the equipment.
Ensure that such materials are not allowed to pollute the environment.
■ The exercise cycle has a magnetic brake system.
■ To operate correctly, the pulse function requires a minimum voltage
of 2,7 volts (only for computers working with batteries).
■ The equipment is dependent of revolutions per minute.
■ Please ensure that liquids or perspiration never enter the
machine or the electronics.
■ Before use, always check all screws and plug-in connections as well
as respective safety devices fit correctly.
■ Always wear suitable shoes when using.
■ Nobody may be in the moving range of a training person during
training
List of spare parts page 22-23
When ordering spare parts, always state the full article number, spare-
partnumber, the quantity required and the S/N of the product (see
handling).
Example order: Art.no. 07662-700 / spare-part no. 10100030 /
2 pieces / S/N ....................
Please keep original packaging of this article, so that it may be used
for transport at a later date, if necessary.
Goods may only be returned after prior arrangement and in (internal)
packaging, which is safe for transportation, in the original box if pos-
sible.
It is important to provide a detailed defect description / damage report!
Important: spare part prices do not include fastening material; if
fastening material (bolts, nuts, washers etc.) is required, this should
be clearly stated on the order by adding the words „with fastening
material“.
Waste Disposal
KETTLER products are recyclable. At the end of its useful life please
dispose of this article correctly and safely (local refuse sites).
KETTLER (GB) Ltd.
Merse Road · North Moons Moat · Redditch,
Worcestershire B98 9HL · Great Britain
http://www.kettler.co.uk
KETTLER International Inc.
P. B. 2747 · Virginia Beach · Virginia Beach, Virginia
23450 USA
http://www.kettlerusa.com
