511243
87
Zoom out
Zoom in
Previous page
1/104
Next page
79
14 CONNECTING PERIPHERAL EQUIPMENT
DX PACKETCLUSTER TUNE
If you have a TM-D700 transceiver, you can connect the TM-D700 to the TS-480 transceiver to use the DX
PacketCluster Tune function. Connect the 2 transceivers with a cross-wired RS-232C cable as shown below.
Configure the TM-D700 transceiver to the DX PacketCluster node frequency.
TS-480 transceiver
TM-D700 transceiver
Cross-wired cable
RESET
GPS
COM
DATA
MIC
PANEL
PADDLE
KEY
E
X
T.S
P
D
AT
A
RE
M
O
TE
C
O
M
M
IC
P
AN
EL
1 Press [MENU/ F.LOCK] and turn the MULTI control to select Menu No. 56 on the TS-480 transceiver.
2 Press [ ]/ [ ] to select the same communication baud rate configured on the TM-D700 transceiver.
3 Tune to the DX PacketCluster node frequency on the TM-D700 transceiver.
4 Press [F] (1 s), [TNC] on the TM-D700 transceiver.
“TNC APRS” appears on the TM-D700 transceiver.
5 Press [F] (1 s), [DX] on the TM-D700 transceiver.
6 Select a desired DX station data with [
cc
cc
c]/ [
dd
dd
d] on the TM-D700 transceiver.
7 Press [MHz] on the TM-D700 transceiver to transfer the frequency data to the TS-480 transceiver.
If the transferred frequency data is available on the TS-480 transceiver, the frequency data will be
overwritten to the current operating frequency. Otherwise, the operating frequency of the TS-480
transceiver remains unchanged.
For more detailed operation on the DX PacketCluster operation of the TM-D700 transceiver, refer to page 6 of the
TM-D700 instruction manual (Specialized Communications).
Note:
The firmware of the TM-D700 transceiver must be version G2.0 or later to use the DX PacketCluster Tune function.
CROSSBAND REPEATER
If you have a TM-D700 transceiver, you can connect the TM-D700 transceiver to the TS-480 transceiver to use
the Crossband repeater function. Connect the 2 transceivers with a mini DIN cable (6-pin) as shown below.
TS-480 transceiver
TM-D700 transceiver
RESET
GPS
COM
DATA
MIC
PANEL
PADDLE
KEY
EX
T.S
P
D
ATA
R
E
M
O
TE
C
O
M
MIC
PANE L
After connecting the 2 transceivers with the cable, access Menu No. 57 (DTS polarity) on the TS-480 transceiver
and select “on”. You will further need to adjust the audio input/ output level of the TS-480 transceiver using Menu
Nos. 46 and 47.
To DATA connector
To DATA connector
TS-480
ANI
ANG
DTS
NC
ANO
SQC
PKD
DE
PKS
PR9
PR1
SQC
Mini DIN
6-pin male
Mini DIN
6-pin male
Mini DIN
6-pin male
q
w
e
r
t
y
TM-D700
q
w
e
r
t
y
qw
ty
er
87


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood TS-480SAT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood TS-480SAT in the language / languages: English as an attachment in your email.

The manual is 6,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood TS-480SAT

Kenwood TS-480SAT User Manual - German - 104 pages

Kenwood TS-480SAT User Manual - Dutch - 104 pages

Kenwood TS-480SAT User Manual - French - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info