477378
33
Zoom out
Zoom in
Previous page
1/36
Next page
33
EN
ENGLISH
Amplifier
Cause
The speaker cords are disconnected.
VOLUME is set to the minimum position.
MUTE is ON.
The SPEAKERS switches are set to OFF.
Speaker cords are short-circuited.
The speaker cord is disconnected.
• The surround speaker cords and/or the center
speaker cord is disconnected.
A surround mode has not been activated.
The surround and/or center volume controls
are set to the minimum level.
The audio cord from the record player is not
connected to the PHONO jacks.
The record player is not grounded.
There are many possible causes for this
problem, depending on the type of DVD player
used.
The input mode is set to digital manual.
The software is copy-guarded.
Remedy
Connect them properly referring to “Connecting
the speakers”. $
Adjust the volume to a proper level.
Turn OFF the MUTE. )
Set the SPEAKERS switch to ON. (
Turn the power off, eliminate the short-
circuiting, then turn on the power again.
Connect it properly referring to “Connecting
the speakers”. $
Connect it properly referring to “Connecting
the speakers”. $
Select a surround mode.
Adjust the speaker levels using the test tone.
*
Insert the audio cord plugs securely into the
PHONO jacks.
Connect the grounding wire to the GND terminal
on the rear panel.
Set the input mode to digital manual before
starting playback of the Dolby Digital source.
9
Press the INPUT MODE key to select to full
auto mode. 9
Copy-guarded video software cannot be
recorded.
Symptom
No sound from the speakers.
The standby indicator blinks and sound is
not output.
Sound is not output from one of the speakers.
Sound is not output from the surround
speakers and / or the center speaker, or their
sound is very soft.
A humming noise is generated when the
PHONO input selector is selected.
When playing a Dolby Digital source signal
using a DVD player, the sound is cut off soon
after it starts.
No sound is produced during playback from
a DVD player.
A video source cannot be recorded normally.
In case of difficulty
Tuner
Cause
No antenna is connected.
The broadcast band is not set properly.
The frequency of the desired station is not
tuned.
Noise due to ignition of an automobile.
Noise due to interference from an electric
appliance.
Noise due to a nearby TV set.
• The preset station belongs to a frequency that
cannot be received.
• The preset memory was cleared because the
power cord had been unplugged for a long
period of time.
Remedy
Connect an antenna. %
Set the broadcast band properly.
Tune the frequency of the desired station.
Install the outdoor antenna away from the
road.
Turn off the power to the appliance.
Install the receiver farther away from the TV.
Preset a station with a receivable frequency.
Preset the station again.
Symptom
Radio stations cannot be received.
Interference.
A station which was preset cannot be
received by pressing the corresponding
numeric key.
Resetting the Microcomputer
The microcomputer may malfunction (unit cannot be operated,
or shows an erroneous display) if the power cord is unplugged
while the power is ON, or due to some other external factor. If
this happens, execute the following procedure to reset the
microcomputer and return the unit to its normal operating
condition.
With the power cord plugged in, turn the POWER ON/
OFF key OFF. Then, while holding down the ON/
STANDBY
key, press POWER ON/OFF key.
Please note that resetting the microcomputer will clear the contents
of the memory and return the unit to the state it was in when it
left the factory
*5339/31-36/EN 10/1/03, 8:36 PM33
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood KRF-V5070D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood KRF-V5070D in the language / languages: English as an attachment in your email.

The manual is 1,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kenwood KRF-V5070D

Kenwood KRF-V5070D User Manual - German - 36 pages

Kenwood KRF-V5070D User Manual - French, Italian, Spanish - 180 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info