550572
22
Zoom out
Zoom in
Previous page
1/24
Next page
22
÷Insert the power plug firmly to the AC outlet.
÷Turn the amplifier’s power ON.
÷Load the disc again with its label side up.
÷Insert the disc properly.
÷
Wipe off the dust on the surface of the disc
referring to “Disc handling precautions”.
9
÷Replace the disc with a new one.
÷Leave the player for about 1 hour so that the
condensation is removed.
9
÷Press the 6 key.
÷Wipe off the dust on the disc surface referring
to “Disc handling precautions”.
9
÷Replace the disc with a new one.
÷Connect all connection cords firmly.
÷Adjust the output level with OUTPUT key on
the remote control unit.
7
÷Wipe off the dust on the disc surface referring
to “Disc handling precautions”.
9
÷Replace the disc with a new one.
÷Try selecting a place where no strong vibra-
tions occur by changing the installation place,
etc.
÷If automatic play is not required, remove the
disc from the player before setting the unit to
POWER OFF.
÷Power plug is loosely connected.
÷With the power plug connected to the switched
AC outlet of an amplifier, the power of the
amplifier is turned off.
÷Disc is loaded upside down.
÷Disc is loose.
÷Disc is dirty.
÷Disc is cracked.
÷Condensation has occurred on the optical lens
unit.
÷Play mode is not entered.
÷Disc is too dirty.
÷Disc is cracked.
÷The connection cords are inserted loosely.
÷Output level is attenuated too low.
÷Disc is too dirty.
÷Disc is cracked.
÷Oscillation is applied to this unit.
÷This unit is designed so that play begins auto-
matically when the unit is turned ON if a disc
is already loaded.
The unit is not turned on with the
POWER switch ON.
Disc is loaded, player does not play.
No sound.
Music is interrupted. (Sound is skipped.)
Play begins as soon as the unit is turned
ON.
Remote control operation is not possi-
ble.
÷Batteries are exhausted.
÷The remote control unit is too far away from
the main system, controlling angle is too large,
or there is an obstacle in between.
÷Replace with new batteries.
!
÷Operate the remote control unit within the
controllable range.
!
In case of difficulty
What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the
table below to see if the problem can be corrected before seeking help from your dealer or service representative.
Operation to reset
The microcomputer may fall into malfunction (impossibil-
ity to operate, erroneous display, etc.) when the connec-
tion cords are unplugged while unit is ON or due to an
external factor. In this case, execute the following method
to reset the microcomputer and return it to normal condi-
tion.
CD player unit
Remote control unit
÷Please be aware that resetting the CD player will erase all stored
information and return it to the factory settings.
Set the unit to POWER OFF by pressing the POWER
key, and after a few seconds, turn the unit POWER ON
by pressing the POWER key again.
Symptom Cause Remedy
Symptom Cause Remedy
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood DPF-2030 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood DPF-2030 in the language / languages: English as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info