536420

Kenwood CMOS 210 Manual

3
Zoom out
Zoom in
Previous page
1/116
Next page
CMOS-310/CMOS-210
|
3
ENGLISH
• Lay the cords by avoiding high-temperature areas. Use
corrugated tubes for wiring inside the engine room. If a
cord contacts a high-temperature area of the vehicle, the
coating may melt and cause short-circuiting, which may
lead to a  re or electric shock hazard.
Accessories
CAUTION
• If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and o with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
• If the fuse blows,  rst make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
• Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
• After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
• Install so that it does not obstruct the rear  eld of view.
• Install so that it does not protrude from the side of the car.
• Do not perform installation in rain or fog.
• When humidity is high, dry the surface to which the unit is
to be attached before installing.
• Moisture on the attachment surface reduces adhesive
strength, which may lead to the unit coming o .
• Do not attach the camera bracket to areas on the car body
treated with  uorocarbon resin, or glass.
• May result in the rear view camera falling o .
- Do not apply water to the unit.
- Do not expose the unit to rain.
- Do not subject the camera to unnecessary force.
- Thoroughly clean where tape is used for sticking on the
unit.
• Refer to the Instruction’s manual for details on connecting
the other units, then make connections correctly.
• Secure the wiring with cable clamps or adhesive tape.
To protect the wiring, wrap adhesive tape around them
where they lie against metal parts.
• Route and secure all wiring so it cannot touch any moving
parts, such as the gear shift, handbrake and seat rails.
• Do not route wiring in places that get hot, such as near the
heater outlet. If the insulation of the wiring melts or gets
torn, there is a danger of the wiring short-circuiting to the
vehicle body.
• When replacing the fuse, be sure to use only fuse of the
rating prescribed on the fuse holder.
• To minimize noise locate the TV antenna cable, radio
antenna cable and RCA cable as far away from each other
as possible.
• Do not install the power supply box unit in places where
it may become subject to high temperatures or humidity,
such as:
- Places close to a heater, vent or air conditioner.
- Places exposed to direct sunlight, such as on top of the
dashboard or the rear shelf.
- Places that may be splashed by rain, for example close to
the door.
Waterproof packing ..........1
Camera bracket clamping screw..........1
Camera (with camera bracket) ..........1
Switch unit..........1
Double-side adhesive tape ..........1
CMOS-310 only
Power cord ..........1
CMOS-310 CMOS-210
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kenwood CMOS 210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kenwood CMOS 210 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 5,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info