686381
22
Zoom out
Zoom in
Previous page
1/26
Next page
EN
3.4 DISPOSAL OF THE MACHINE
Do not dispose of electrical equipment with normal waste!
In observance of European Directive 2002/96/EC on waste electrical and electronic
equipment, and its implementation in accordance with national law, electrical equipment
that has reached the end of its life must be collected separately and taken to an appropriate
environmentally responsible recycling facility.
The owner of the equipment is obliged to deliver a decommissioned unit to a regional
collection centre, per the instructions of local authorities or a Kemppi representative. By
applying this European Directive you will improve the environment and human health.
4. TROUBLESHOOTING
In the event of a failure of the machine, contact an authorised Kemppi service agent. Before
taking your unit for servicing, check the list below.
4.1 OVERLOAD YELLOW INDICATOR LIT
Two simultaneously operating fans cool the power source. The machine may, however,
overheat if continuously loaded above the rated values or if the circulation of cooling air is
prevented.
Overheating is indicated by a yellow indicator light in the front panel of the power source. You
then need to stop welding and let the machine cool down. The indicator light turns o when
welding can be resumed.
4.2 CONTROL CABLE CONNECTOR FUSE
The back panel of the power source has a fuse that protects the control cable connector. Using
an incorrect type of fuse will damage the power source. Therefore, it is important that you
always use the correct fuse type. The type and size of the fuse are indicated next to the fuse
socket.
4.3 ELECTRIC NETWORK OVERVOLTAGE OR UNDERVOLTAGE
If the power source is used in an electric network with insucient voltage (less than 300 V),
the control features of the device are automatically disabled.
The primary circuits of the power source are protected against power spikes. The products
mains voltage range is broad enough to prevent over-voltage problems at up to 440 V. Make
sure that the voltage remains within the allowed range, especially if the operating power is
supplied by a generator set. For information on the allowable voltage range, see "Technical
specications" in this guide.
4.4 MISSING PHASE IN THE ELECTRIC NETWORK
If a phase is missing from the mains current, the welding features will be adversely aected or
the machine may have problems starting. Loss of a phase can be caused by a:
• Blown mains fuse
• Damaged mains cable
• Poor mains cable connection in the machine’s terminal block or mains socket
4.5 ERROR CODES
The machine always checks its operation automatically during start-up and reports any
failures detected. If failures are detected during start-up, they are shown as error codes on the
control panel display.
Err3: Power source overvoltage
The machine has stopped the welding because it has detected momentary voltage spikes or
continuous overvoltage dangerous to the machine in the electric network. Check the quality
of the supply network.
20
KempArc SYN 300, 400, 500, DT 400 / © Kemppi Oy / 1117
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi Kemparc SYN 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi Kemparc SYN 300 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info