686381

Kemppi Kemparc SYN 300 Manual

14
Zoom out
Zoom in
Previous page
1/26
Next page
EN
2.2.9 Optional additional MIG features
In addition to the additional MIG features included in the standard delivery, it is also possible
to acquire optional features that further expand the operating features of the machine.
To use the optional features, enter a machine-specic activation code in the machine's control
panel as shown below. To purchase an activation code, contact a Kemppi representative.
Activating optional additional features
1. Press and hold down the SETUP button P8 for at least 5 seconds. The SETUP settings
menu appears on the display.
2. Select the Cod alternative with the left-hand side control knob in the control panel and
then select the value Ent using the right-hand side control knob.
3. Briey press the SAVE button.
4. When the display on the left-hand side reads 1, enter the rst value of the activation
code using the right-hand side control knob. The value you have entered is shown in the
right-hand side display.
5. Select the entry of the next value using the left-hand side control knob.
6. Enter the value corresponding to the value shown in the left-hand side display using the
right-hand side control knob.
7. Repeat steps 5 and 6 until you have entered all values of the activation code.
8. Finally, press the SAVE button briey.
The control panel will read Suc cEs to indicate that the activation code has been entered
correctly and the additional feature is available. You can exit the code entry mode at any time
by briey pressing ESC.
If the code entry failed, the control panel display will show an error code. For more
information on error codes, see "Troubleshooting".
The operating instructions for optional additional features can be found in the documentation
supplied with the additional feature.
2.2.10 Memory features (MEMORY button)
Use the control panel memory features to store welding parameters you use into the
machine's memory for easy use later without the need to readjust all parameters. The control
panel has 90 memory positions, numbered 0...89.
You can store the welding parameters you use, i.e., the wire feed speed and the welding
voltage. You can also store additional feature settings, such as creep start or crater ll settings.
Storing welding parameters in memory
1. Press the MEMORY button twice. If a memory channel is free, the SET indicator starts
ashing. In other cases the indicator will be turned on constantly.
(If the memory is empty, one push of the button is enough.)
2. Select the memory channel you want using the CH button.
3. Specify the welding settings you want and store the selections by pressing SAVE.
4. Press the MEMORY button twice. The ON indicator light will turn on and the welding
parameters you selected are activated.
5. Start welding.
If you want to change the welding parameters stored in a welding channel, go to the SET
mode by pressing the MEMORY button. Now select the parameters you want and store them
by pressing SAVE.
You can also store the welding parameters with the SET button when the memory feature is in
the OFF state, i.e., when the MEMORY indicators are not on.
To clear the data in a memory channel, press the MEMORY and CH buttons simultaneously
when the control panel is in the SET mode (the SET indicator is on).
Using stored welding parameters
6. Press the MEMORY button to turn on the ON indicator.
7. Select the memory channel you want from the robot.
8. Start welding.
12
KempArc SYN 300, 400, 500, DT 400 / © Kemppi Oy / 1117
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi Kemparc SYN 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi Kemparc SYN 300 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info