686374

Kemppi A7 Robot Gun Mount T3 Manual

19
Zoom out
Zoom in
Previous page
1/21
Next page
19
Robot Gun Mount T3© Kemppi Oy 2016 1712
OPERATING MANUAL
16. REMOVING THE MOUNT
This section describes how to remove robot mount T3.
Unmounting may only be carried out by specialist personnel. Please make sure
that the shutdown procedures are strictly observed before the unmounting work
begins. Ensure this also for the components integrated into the welding system.
Risk of injury due to unexpected start-up
For the entire duration of maintenance, servicing, unmounting, and repair work, the
following instructions must be adhered to:
• Switch o the power supply.
• Cut o the compressed air supply.
• Pull the power plug.
Removal from operation depends on the type of welding gun. Please observe the
operating instructions of the A7 MIG Gun 500-g or the A7 MIG Gun 500-w welding
guns, as appropriate.
Proceed as follows:
1. Disconnect the hose assembly from the wire feeder.
2. Open the lock ring, and unscrew the fastening screw. See Section 11.3.
3. Pull out the hose assembly.
4. Disconnect the gun neck, and remove it. See sections 11.4 and 11.5.
16.1 Disposal
For disposal, the locally applicable regulations, laws, provisions, standards, and
guidelines must be observed. For the welding torch system to be properly disposed
of, it must be unmounted rst.
16.2 Materials
This product consists for the most part of plastics, steel, and non-ferrous metals. Steel
and non-ferrous metals can be melted down, so iron products are almost innitely
recyclable. The plastic materials used are marked in preparation for appropriate
sorting of the materials for later recycling.
16.3 Consumables
Oils, greases, and cleaning agents must not contaminate the ground or enter the
sewer system. These materials must be stored, transported, and disposed of in suitable
containers. Please observe the relevant local regulations and the disposal instructions
on the safety data sheets supplied by the manufacturer of the consumables. Also,
contaminated cleaning tools (brushes, rags, etc.) must be disposed of in accordance
with the information provided by the manufacturer of the consumables.
16.4 Packaging
The shipping packaging has been reduced to a minimum. Packaging materials are
always selected with attention to their recyclability.
… 19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemppi A7 Robot Gun Mount T3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemppi A7 Robot Gun Mount T3 in the language / languages: English as an attachment in your email.

The manual is 1,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info