778309
55
Zoom out
Zoom in
Previous page
1/60
Next page
DT ISTR_6541091_04/21 55/60
Brûleur qui ne s’allume
pas
Faible pression
Ouverture bloquée
Contrôle pas ouvert
Mauvais thermocouple
Pièce de la flamme d’allumage
tordue
Pas placé au bon endroit
Réservoir presque vide, le remplir
au besoin
Enlever et nettoyer
Tourner la soupape sur ON
Remplacer le thermocouple
Placet la flamme d’allumage
correctement
Remettre en bonne position et
essayer à nouveau
Flamme du brûleur faible
Tuyau d’alimentation tordu
Remettre le tuyau en place et
vérifier s’il y a une fuite
Émetteur non uniforme
Faible pression du gaz
La base n’est pas sur une surface
plane
Remplacer le réservoir
Mettre sur une surface plane
Fumée noire épaisse
Blocage dans le brûleur
Fermer l’appareil et le laisser
refroidir. Enlever le blocage et
dégager l’intérieur et l’extérieur du
brûleur.
Résidu charbonneux
Saleté ou film sur le réflecteur et le
pare-flammes
Nettoyer le réflecteur et le pare-
flammes
GB PROBLEMS CHECK LIST
PROBLEM
PROBABLE CAUSE
SOLUTION
Pilot will not light
Gas valve may be OFF
Tank fuel empty
Opening blocked
Air in supply system
Loose connection
Low gas pressure
Turn the gas valve ON
Refill LPG tank
Clean or replace opening
Purge air from lines by pressing the
control knob until you smell gas
Check all fittings
Replace cylinder with a new cylinder
Pilot will not stay on
Debris around pilot
Loose connection
Thermocouple bad
Gas leak in line
Lack of fuel pressure
Clean dirty area
Tighten connections
Replace thermocouple
Check connections
Tank near empty. Refill or replace
LPG tank
Burner will not light
Pressure is low
Opening blocked
Control not ON
Thermocouple bad
Pilot light assembly bent
Not in correct location
Tank near empty. Refill or replace
LPG tank
Remove and clean
Turn valve to ON
Replace thermocouple
Place pilot properly
Position properly and retry
Burner flame is low
Supply hose is bent or twisted
Straighten hose and perform leak test
on hose
Emitter glows uneven
Low gas pressure
Base is not on a level surface
Replace cylinder with a new cylinder
Place heater on a level surface
Thick black smoke
Blockage in burner
Turn off the heater and let it cool.
Remove blockage and clear burner
inside and outside
Carbon build-up
Dirt or film on reflector and flame
screen
Clean reflector and flame screen
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kemper 6541091 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kemper 6541091 in the language / languages: English, German, French, Italian, Spanish, Norwegian as an attachment in your email.

The manual is 1.45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info