771564
9
Zoom out
Zoom in
Previous page
1/12
Next page
owner's manual
5
4. MAINTENANCE
4.1 Confirmation before operating
1.
Make sure if the ground wire is broken or fall off.
2.
Make sure if a air strainer has been installed.
3.
Start the power supply switch 12 hours before operating.
4.3 Error information and code
4.2 NON-A/C errors
1.
For common protections, please refer to indoor unit operation
manual.
2.
For NON-A/C errors, please refer to indoor unit operation manual.
If the following situation happens, please stop the unit and cut off the power supply and contact with local customer service center.
Table 4-1
Display
Code
Malfunction or Protection
Remarks
1
E0
Outdoor unit COMM.Error
2
E1
Phase protection
3
E2
COMM.Error with indoor unit
In or after 20min,communication breaks 2 times for the first time to electrified
4
E4
Outdoor Temp. sensor error
5
E5
Voltage protecation
6
E7
Discharge sensor error
If discharge temp. is below 15for 5 min after 10 minutes operating,
displays E7, when GAS is higher than 25, it recovers
7
E8
Outdoor unit address error
8
xE9
Wrong drive model
X represents in which system, 1 is system A, 2 is system B
9
EA
5-min protection in A zone(heating fan)
10
xH0
COMM. Error between IR341 and main chip
X represents in which system, 1 is system A, 2 is system B
11
H1
COMM. Error between 0537 and main chip
12
xH4
3 times of P6 protection in 60 munites
X represents in which system, 1 is system A, 2 is system B,
Not recoverable unitil re-power on
13
H5
3 times of P2 protection in 60 munites
Not recoverable until re-power on
14
H6
3 times of P4 protection in 100 munites
Not recoverable until re-power on
15
H7
Qty.of indoor units decreases error
Indoor unit lost for over 3 munites; not recoverable,until the unit qty. recover
16
H9
3 times of P9 protection in 60 minutes
Not recoverable until re-power on
17
dF
Defrosting
18
d0
Oil returning
19
P1
High pressure protection or discharge
temperature switch protection
20
P2
Low pressure protection
21
xP3
Compressor current protection
X represents in which system, 1 is system A, 2 is system B
22
P4
High discharge Temp.Protection
23
P5
High condenser Temp.Protection
24
xP6
Inverter module protection
X represents in which system, 1 is system A, 2 is system B
25
P9
DC fan protection
26
PE
Evaporator T2 high temp. protection
27
PL
The Temp.protection of inverter module
28
C7
3 times of PL protection in 90 minutes
Not recoverable until re-power on
29
xL0
DC compressor module error
X represents in which system, 1 is system A, 2 is system B
30
xL1
DC bus low pressure protection
X represents in which system, 1 is system A, 2 is system B
31
xL2
DC bus high voltage protection
X represents in which system, 1 is system A, 2 is system B
32
xL4
MCE malfunction/simultaneously/cycle loop
X represents in which system, 1 is system A, 2 is system B
33
xL5
Zero speed protection
X represents in which system, 1 is system A, 2 is system B
34
xL7
Compressor wrong phase protection
X represents in which system, 1 is system A, 2 is system B
35
xL8
Compressor speed difference in one
second more than 15rps
X represents in which system, 1 is system A, 2 is system B
36
xL9
Compressor speed difference between setting
speed and running speed more than 15rps
X represents in which system, 1 is system A, 2 is system B
If the problem still existing, please contact the sales distributor or the service center, tell us your model No. and the detail of the error.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kaysun Amazon Unitario KMF-400 DN3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kaysun Amazon Unitario KMF-400 DN3 in the language / languages: English as an attachment in your email.

The manual is 2.13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kaysun Amazon Unitario KMF-400 DN3

Kaysun Amazon Unitario KMF-400 DN3 User Manual - German - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info