631810
3
Zoom out
Zoom in
Previous page
1/20
Next page
Grundeinheit UFG 312
Basic module carrier UFG 312
Ensemble de base UFG 312
936.2170 /C/0403/3.12 def
Grundeinheit UFG 308
Basic module carrier UFG 308
Ensemble de base UFG 308
Abstand zur Decke min. 100 mm
Distance to ceiling 100 mm min. / Ecart vers le plafond 100 mm min.
Abstand zur Decke min. 100 mm
Distance to ceiling 100 mm min. / Ecart vers le plafond 100 mm min.
21
Montageschritte
(Bild 1 + 2)
Grundeinheit oder Erweiterungseinheit
mit 3 Schrauben auf ebenem
Untergrund montieren.
Größere Unebenheiten ausgleichen.
Am Gehäuse Potentialausgleich
vorschriftsmäßig durchführen.
(DIN EN 50083-1/VDE 0855 Teil 1).
Eingangsverteiler entsprechend der
Anlagenplanung an die Sat-ZF-Nieder-
führungen (H und V) anschließen
(F-Connector). Dazu gegebenenfalls
die HF-Verbindungsleitungen zwi-
schen den Verteilern entfernen und
Abschlusswiderstände
umstecken.
Hinweis:
Eine Fernspeiseweiche ist in den
Grundeinheiten UFG 308 und UFG 312
bereits enthalten und betriebsbereit
angeschlossen.
(LNB-Spannung 18 V, an die horizon-
tale Polarisation der Sat-ZF-Nieder-
führung anschließen).
Wenn ein weiteres LNB in der Sat-
Empfangsanlage vorhanden ist, muss
ein separates Fernspeisenetzteil
NCF 31 verwendet werden.
Installation procedure
(Fig. 1+2)
Fasten basic module carrier or exten-
sion module carrier with 3 screws,
on an even surface.
Compensate any unevenness.
Ground the housing according to DIN
EN 50083-1/VDE 0855 part 1.
Connect output splitters with the Sat IF
downleads (hor. + vert.) (F-connector) in
compliance with system plan.
If required remove RF connection
cables located between the splitters
and change the plug position of the
terminating resistors
.
Note:
A remote feed diplexer ready for ope-
ration is pre-mounted on the basic
module carriers UFG 308 and UFG 312
(the LNB current 18 V, will be
connected to hor. polarisation
of Sat IF downlead).
In the event that the Sat reception
system comprises another LNB, it is
necessary to install a separate remote
power supply unit NCF 31.
Etapes de montage
(Fig. 1+2)
Monter l’ensemble de base ou
l’ensemble de extension sur une paroi
plane à l’aide de 3 vis. Supprimer les
plus grosses inégalités.
Mettre les boîtiers à la terre selon les
règlements (DIN EN 50083-1/VDE 0855
partie 1).
Brancher (connecteur F) le répartiteur
d’entrée aux descentes de câble FI Sat
(H et V) conformément au plan de
l’installation.
Le cas échéant, supprimer les liaisons
HF entre les répartiteurs et connecter
des résistances de terminaison
.
Remarque:
Les ensembles de base UFG 308 et
UFG 312 comportent déjà une déri-
vation pour la téléalimentation prête
à être branchée (tension LNB 18V,
à brancher à la polarisation horizontale
de la descente FI Sat).
Si un autre LNB est présent dans le
système de réception satellite,
employer un bloc de téléalimentation
séparé NCF 31.
3
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kathrein UFG 312 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kathrein UFG 312 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info