612218

Kalorik CM 25282 - K111026 Manual

5
Zoom out
Zoom in
Previous page
1/24
Next page
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Team
International BELGIUM. The pages must be reproduced and
folded in order to obtain a booklet A5 (+/- 148.5 mm width x
210 mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don’t change
the page numbering. Keep the language integrity. Print only
what is inside the frame.
5 USK CM 25282 - 111026
Assembly page 5/24
Fax +32 2 359 95 50
PREPARATION OF COFFEE
• Open the lid of the water tank and pour the desired volume of water in
it. The water level can be read off the water level indicator. Never
exceed the maximum level indicated.
• Insert filter paper in the filter holder and add the desired quantity of
ground coffee using the provided scoop.
• Never forget to close the water tank lid before switching on the coffee
maker.
• Put the jug with closed lid on the hotplate.
• Plug in the coffee maker. Press the ON/OFF button once. The red RUN
light, will be illuminated, indicating that your appliance is in use. Thanks
to the keep warm function, your coffee stays warm as long as the
appliance is switched on (for 2 hours, unless coffee maker gets switched
off by user)
• Your coffee maker is equipped with a “Pause-and-Serve” function,
which means that when you remove the jug from the appliance, a non-
drip valve will automatically operate to stop any drops of coffee falling
onto the hotplate. When you put the jug back into place, the non-drip
valve opens automatically and allows remaining coffee to filter through
into the jug.
• Wait until the brewing process is finished and the filter is empty before
removing the jug.
• Practical hints: When the water tank is empty, wait a few more minutes,
as some water might still drip out of the filter before removing the jug.
• Note: a 2-hour auto-shut off feature is activated when operating the
coffee maker manually
PROGRAMMING THE COFFEE MAKER
• To program your coffee maker to brew fresh coffee at a preset time, first
follow steps 1 to 4 in the “PREPARATION OF COFFEE” section.
• Make sure the coffee maker’s clock is set to the right time.
• Press the PROG button twice. The clock will now display 12:00 with the
word “TIMER” in the upper left corner. Use the HOUR and MINUTE buttons
to set the desired brew time. Press PROG to validate the timer setting.
• Press the START/STOP button twice to activate the preset brew cycle.
The green AUTO light will illuminate when the brew time is properly set.
• When your preset brew time is reached and the coffee maker starts its
brew cycle, the green AUTO light will go out and the red ON light will
illuminate.
• As with the regular brew cycle, an automatic two hour keep warm
cycle will commence after your coffee maker has finished brewing. At
the end of the two hours, the coffee maker will automatically shut itself
off.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kalorik CM 25282 - K111026 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kalorik CM 25282 - K111026 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info