531838
2
Zoom out
Zoom in
Previous page
1/6
Next page
Alarmzentrale Schlüsselschalter AP/UP
Art.-Nr.: DAS 4300 A
DAS 4300 U
Den Zylinder mittels der beigefügten M5-Schraube (Sechskant-Kopf -
8mm Gabelschlüssel) und Federscheibe an dem dafür vorgesehenen
Winkel am Gehäusedeckel befestigen.
Prüfen, ob der Schließbart des Zylinders die Schalter einwandfrei
betätigt, indem der Gehäusedeckel in das Gehäuse gelegt wird und der
Zylinder in beide Stellungen gedreht wird. Dabei müssen die Schalter
S1 und S2 betätigt werden.
4. Montage Gehäuse
4.1. Aufputz:
Das Gehäuse wird mit vier Schrauben an einer ebenen und stabilen Fläche
befestigt. Darauf achten, dass das Gehäuse nicht verzogen wird und der
Sabotageschalter (Abreißkontakt) sicher schalten kann.
Das Anschlusskabel durch die obere runde Öffnung in das Gehäuse führen
und auf ca. 15 cm ablängen und abmanteln.
4.2. Unterputz:
Aus der Wand einen Ausbruch ausstemmen, so dass das Gehäuse bündig
mit dem Putz abschließt:
H x B x T. ca. 115mm x 75mm x 52mm.
Das Anschlusskabel durch die obere runde Öffnung in das Gehäuse führen
und auf ca. 15 cm ablängen und abmanteln.
Gehäuse einputzen.
Achtung! Nur die obere runde Öffnung zur Kabeleinführung
verwenden. Beigelegten Kabelbinder zur Kabelzugentlastung um
das Kabel, nahe am Gehäuseboden, festbinden.
Gehäuse an Erdungslasche (links von Kabeleinführung) erden.
5. Umstellen der Kontaktsätze
Auslieferungszustand:
Scharf-/Unscharf-Schalter (S/US): Rastbetrieb
Test-Schalter (TS): Tastbetrieb
Die Rastfeder schalterseitig (nicht betätigerseitig!) vorsichtig aushängen,
dadurch wird von Rastbetrieb auf Tastbetrieb umgestellt.
Bitte beachten: die Rastfeder niemals an der Betätigerseite aushängen,
sonst fällt der Schalter auseinander.
Schalterseite
Betätigerseite
Rastschalter Tastschalter
5.1. Verdrahtung
Das abgemantelte Kabel nach Anschlussplan anschließen.
2
Die LEDs können über die eingebauten Vorwiderstände (R1/R2) oder
direkt angesteuert werden. Bei direkter Ansteuerung muss die
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jung DAS 4300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jung DAS 4300 in the language / languages: German as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info