614555
50
Zoom out
Zoom in
Previous page
1/51
Next page
– 48 –
No.
Description of error
detected
Cause of occurrence expected Items to be checked
E000 Execution of data
initialization (This is
not the error.)
• When the machine head is changed.
• When the initialization operation is exe-
cuted.
E007 Overload of motor • When the machine head is locked.
• When sewing extra-heavy material
beyond the guarantee of the machine
head.
• When the motor does not run.
• Motor or driver is broken.
• Check whether the thread has been entan-
gled in the motor pulley.
• Check the motor output connector (4P) for
loose connection and disconnection.
• Check whether there is any holdup when
turning the motor by hand.
E071 Disconnection of mo-
tor output connector
• Disconnection of motor connector. • Check the motor output connector for loose
connection and disconnection.
E072 Overload of motor
at the time of thread
trimming motion
• Same as E007. • Same as E007.
E079 Continuous opera-
tion with the motor
applied with a higher
load
• The machine has been operated with the
motor applied with a load which is higher
than the normal load.
• Check whether the thread has been entan-
gled in the motor pulley.
• Check whether there is any holdup when
turning the motor by hand.
E302 Fall detection switch
failure
(When the safety
switch works)
• When fall detection switch is input in the
state that the power is turned ON.
• Check whether the machine head is tilted
without turning OFF the power switch
(sewing machine operation is prohibited for
safety sake).
E303 Semicircular plate
sensor error
• Semicircular plate sensor signal cannot
be detected.
• Check whether the motor encoder connec-
tor is disconnected.
E499
E704
Data fault • The stored data have broken.
E730 Encoder failure • When the motor signal is not properly
inputted.
• Check the motor signal connector (CN30)
for loose connection and disconnection.
• Check whether the motor signal cord has
broken since the cord is caught in the ma-
chine head.
• Check whether the inserting direction of the
motor encoder connector is wrong.
E731 Motor hole sensor
failure
E733 Inverse rotation of
motor
• This error occurs when the motor is run-
ning at 500 sti/min or more in the oppo-
site direction of that of rotation indication
during motor is running.
• Connection of the encoder of main shaft
motor is wrong.
• Connection for the electric power of main
shaft motor is wrong.
E799 Thread trimming
operation time-out
• The thread trimmer control operation is
not completed within the predetermined
time period.
E808 Solenoid short circuit • Solenoid power does not become normal
voltage.
• Check whether the machine head cord is
caught in the cover or the like.
E809 Holding motion
failure
• Solenoid is not changed over to holding
motion.
• Check whether the solenoid is abnormally
heated. (CTL circuit board asm. circuit is
broken.)
E810 Solenoid current
abnormality
• Solenoid rare short-circuit. • Solenoid resistance.
E811 Overvoltage • When voltage higher than guaranteed
one is inputted.
• 220V is applied to 120V box.
• CE : 400V is applied to 230V box.
• Check whether the applied power voltage is
higher than the rated voltage + (plus) 10%
or more.
• The power PCB may have broken.
Error code list
50


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Juki DDL8700B-7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Juki DDL8700B-7 in the language / languages: English as an attachment in your email.

The manual is 6,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info