28358

JRC Radar3000 Manual

23
Zoom out
Zoom in
Previous page
1/55
Next page
16
⑥ Put the EBL over the desired target using the J-DIAL, and press the JOY-
STICK.
⑦ Move the EBL so that the target will be displayed on the SHM.
⑧ Press the JOYSTICK to end the bearing adjustment mode.
3.7.4 DISPLAY TIMING (ZERO NM ADJUSTMENT)
This alignment must be made when the radar unit is installed. Failure to per-
formed this procedure can result in correct target distance readings. Set the
range at 0.25 NM and observe a target at a known (nearest) distance.
① Locate a straight dock, sea wall or bridge.
Press and hold the JOYSTICK for the initial setting menu.
② Select DISPLAY TIMING by using the JOYSTICK, and press the JOY-
STICK.
③ Adjust distance so that the object appears to be straight on the display by
using the J-DIAL.
④ Press the JOYSTICK to end the display timing adjustment mode.
3.7.5 TUNE PRESET
Follow the instructions given below to make coarse tuning of the receiver : if
after about 10 minutes of transmit, the tune bar is oriented towards one end of
its range for video peak, perform the following steps:
PUSHING
DISPLAY TIMING EARLY
CORRECT
PULLING
DISPLAY TIMING LATE
INSTALLATION
16
⑥ Put the EBL over the desired target using the J-DIAL, and press the JOY-
STICK.
⑦ Move the EBL so that the target will be displayed on the SHM.
⑧ Press the JOYSTICK to end the bearing adjustment mode.
3.7.4 DISPLAY TIMING (ZERO NM ADJUSTMENT)
This alignment must be made when the radar unit is installed. Failure to per-
formed this procedure can result in correct target distance readings. Set the
range at 0.25 NM and observe a target at a known (nearest) distance.
① Locate a straight dock, sea wall or bridge.
Press and hold the JOYSTICK for the initial setting menu.
② Select DISPLAY TIMING by using the JOYSTICK, and press the JOY-
STICK.
③ Adjust distance so that the object appears to be straight on the display by
using the J-DIAL.
④ Press the JOYSTICK to end the display timing adjustment mode.
3.7.5 TUNE PRESET
Follow the instructions given below to make coarse tuning of the receiver : if
after about 10 minutes of transmit, the tune bar is oriented towards one end of
its range for video peak, perform the following steps:
PUSHING
DISPLAY TIMING EARLY
CORRECT
PULLING
DISPLAY TIMING LATE
INSTALLATION
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRC Radar3000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRC Radar3000 in the language / languages: English as an attachment in your email.

The manual is 3,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info