28358
19
Zoom out
Zoom in
Previous page
1/55
Next page
12
CAUTION
INSTALLATION
3.6 ELECTRICAL CONNECTION
3.6.1 DC POWER CABLE
The RADAR 3000 will work with any ship’s mains within the 10.2 to 42 V
range, since it contains a power regulator circuit. Connect the power cable to a
DC source. The power cable normally should be wired through the circuit breaker.
The white lead wire of the power cable should be connected to the positive
source terminal and the black lead to negative source terminal. The shielded
wire should be connected to the ship’s RF ground. Should the power connec-
tions be inadvertently reversed, a protective fuse will blow. Recheck the input
power leads for correct polarity with a VOM and reconnect the leads observing
correct polarity. Replace the fuse.
3.6.2 EXTERNAL SYSTEM INTERFACE
FIG. 3-4 SCANNER UNIT CABLE CONNECTION PROCEDURE
Ground Terminal
Clamping Plate
Rubber Grommet
Interconnecting Cable
Cable Clamp
TO CME-229
J1
P1
W1
PW1
To connect with NAV-AID and/or compass, make sure pin as-
signment, if used same connector.
In case of different pin assignment, the RADAR 3000 or con-
nected NAV-AID will be damaged.
12
CAUTION
INSTALLATION
3.6 ELECTRICAL CONNECTION
3.6.1 DC POWER CABLE
The RADAR 3000 will work with any ship’s mains within the 10.2 to 42 V
range, since it contains a power regulator circuit. Connect the power cable to a
DC source. The power cable normally should be wired through the circuit breaker.
The white lead wire of the power cable should be connected to the positive
source terminal and the black lead to negative source terminal. The shielded
wire should be connected to the ship’s RF ground. Should the power connec-
tions be inadvertently reversed, a protective fuse will blow. Recheck the input
power leads for correct polarity with a VOM and reconnect the leads observing
correct polarity. Replace the fuse.
3.6.2 EXTERNAL SYSTEM INTERFACE
FIG. 3-4 SCANNER UNIT CABLE CONNECTION PROCEDURE
Ground Terminal
Clamping Plate
Rubber Grommet
Interconnecting Cable
Cable Clamp
TO CME-229
J1
P1
W1
PW1
To connect with NAV-AID and/or compass, make sure pin as-
signment, if used same connector.
In case of different pin assignment, the RADAR 3000 or con-
nected NAV-AID will be damaged.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRC Radar3000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRC Radar3000 in the language / languages: English as an attachment in your email.

The manual is 3,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info