28358

JRC Radar3000 Manual

14
Zoom out
Zoom in
Previous page
1/55
Next page
7
SECTION 3
This section provides practical guidelines to assist in the planning and installa-
tion of the RADAR 3000 aboard your vessel.
3.1 UNPACKING AND INSPECTION
Use care when unpacking the RADAR 3000 radar from the shipping carton to
prevent damage to the contents. It is also good practice to save the carton and
the interior packing material until the radar has been satisfactorily installed on
the vessel. The original packing material should be used in the unlikely event
that it is necessary to return the unit for service.
3.2 PLANNING THE INSTALLATION
The layout for installing the RADAR 3000 should be planned to give the best
operation and service aboard your particular vessel. In general, the scanner unit
should be mounted as high as possible above the waterline. The display unit
should be installed in a convenient viewing position near the helm. Keep in
mind the optimum viewing angle when installing the display. You may want to
apply power in advance of installing the unit as that you can determine a satis-
factory viewing angle.
A 10 meter length of interunit cable is furnished for interconnecting the two
main units (scanner and display). This length of interunit cable should be suffi-
cient to complete the cable run required on most small vessels. It is recom-
mended that the maximum length of interunit cable not exceed 20 meters.
A general system diagram for the RADAR 3000 is shown on the following
page.
INSTALLATION
INSTALLATION
7
SECTION 3
This section provides practical guidelines to assist in the planning and installa-
tion of the RADAR 3000 aboard your vessel.
3.1 UNPACKING AND INSPECTION
Use care when unpacking the RADAR 3000 radar from the shipping carton to
prevent damage to the contents. It is also good practice to save the carton and
the interior packing material until the radar has been satisfactorily installed on
the vessel. The original packing material should be used in the unlikely event
that it is necessary to return the unit for service.
3.2 PLANNING THE INSTALLATION
The layout for installing the RADAR 3000 should be planned to give the best
operation and service aboard your particular vessel. In general, the scanner unit
should be mounted as high as possible above the waterline. The display unit
should be installed in a convenient viewing position near the helm. Keep in
mind the optimum viewing angle when installing the display. You may want to
apply power in advance of installing the unit as that you can determine a satis-
factory viewing angle.
A 10 meter length of interunit cable is furnished for interconnecting the two
main units (scanner and display). This length of interunit cable should be suffi-
cient to complete the cable run required on most small vessels. It is recom-
mended that the maximum length of interunit cable not exceed 20 meters.
A general system diagram for the RADAR 3000 is shown on the following
page.
INSTALLATION
INSTALLATION
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRC Radar3000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRC Radar3000 in the language / languages: English as an attachment in your email.

The manual is 3,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info