28360

JRC Radar2000 Manual

31
Zoom out
Zoom in
Previous page
1/54
Next page
24
④ Rotate the J-DIAL clockwise for outer direction or counterclockwise
for inner direction to move the #2 variable range marker. The actual
target distance appears on the center top of the screen in selecting unit.
To turn off the #2 VRM, selects the FUNCTION-#2 VRM-OFF on the
menu sheet.
(4) Using cursor
Touch the JOYSTICK, cross cursor appears on the screen. The cross mark
will be move any direction by using the JOYSTICK and the range and bear-
ing Time-To-Go data and Lat/Loug of the cursor position will be displayed
on the lower right corner on the display.
The cross cursor and cursor data will disappear in approximately 15 sec-
onds.
4.12 BEARING MEASUREMENT
(1) Using the bearing scale
Using the bearing scale on the screen, visually estimate the bearing where
the radial line of the bearing scale would pass through the center of the
target. The bearing you obtain will be the target’s relative bearing in de-
grees.
(2) Using #1 EBL
Press the EBL/VRM key.
If VRM is highlighted, press and hold the EBL/VRM key to change to EBL
mode.
Rotate the J-DIAL clockwise or counterclockwise to move the electronic
bearing line to the center of the target. Target bearing appears on the center
top of the screen in degrees. Bearing may be displayed in relative “R”, true
“T”, or magnetic “M” depending on the menu selection.
To turn off the EBL, press the EBL/VRM key while EBL is highlighted.
(3) Using #2 EBL
① Press the JOYSTICK.
② Selects FUNCTION menu, then press the JOYSTICK.
③ Selects #2 EBL-SET, then press the JOYSTICK. The EBL2 appears high-
light on the upper right corner of the display.
④ Rotate the J-DIAL clockwise or counterclockwise to move the #2 EBL
OPERATION
24
④ Rotate the J-DIAL clockwise for outer direction or counterclockwise
for inner direction to move the #2 variable range marker. The actual
target distance appears on the center top of the screen in selecting unit.
To turn off the #2 VRM, selects the FUNCTION-#2 VRM-OFF on the
menu sheet.
(4) Using cursor
Touch the JOYSTICK, cross cursor appears on the screen. The cross mark
will be move any direction by using the JOYSTICK and the range and bear-
ing Time-To-Go data and Lat/Loug of the cursor position will be displayed
on the lower right corner on the display.
The cross cursor and cursor data will disappear in approximately 15 sec-
onds.
4.12 BEARING MEASUREMENT
(1) Using the bearing scale
Using the bearing scale on the screen, visually estimate the bearing where
the radial line of the bearing scale would pass through the center of the
target. The bearing you obtain will be the target’s relative bearing in de-
grees.
(2) Using #1 EBL
Press the EBL/VRM key.
If VRM is highlighted, press and hold the EBL/VRM key to change to EBL
mode.
Rotate the J-DIAL clockwise or counterclockwise to move the electronic
bearing line to the center of the target. Target bearing appears on the center
top of the screen in degrees. Bearing may be displayed in relative “R”, true
“T”, or magnetic “M” depending on the menu selection.
To turn off the EBL, press the EBL/VRM key while EBL is highlighted.
(3) Using #2 EBL
① Press the JOYSTICK.
② Selects FUNCTION menu, then press the JOYSTICK.
③ Selects #2 EBL-SET, then press the JOYSTICK. The EBL2 appears high-
light on the upper right corner of the display.
④ Rotate the J-DIAL clockwise or counterclockwise to move the #2 EBL
OPERATION
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRC Radar2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRC Radar2000 in the language / languages: English as an attachment in your email.

The manual is 5,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info