28344
328
Zoom out
Zoom in
Previous page
1/404
Next page
A-10
APPENDI
X
3. REFERENCES
Preheating Time after Pattern Selection
After switching over the interswitch patterns, it is necessary to wait for the time as
mentioned below because the pre-heat time is different from the previous
interconnection between the MTR and the display unit. This measure is taken for
protecting the electronic tube emitting radar pulses.
(a) Not changed to the new interconnection condition:.........................No preheat
time
(b) Changed to the new interconnection condition.
However, the MTR was used before change:...........................................30
seconds
(c) Changed to the new interconnection condition.
However, the MTR was used before change:.............................................3
minutes
Notes on Pattern Selection
Immediately after switching over the patterns, the try to select another pattern may fail.
This means that even If the pattern switchover is completed, it takes some time to
prepare for the next interswitch operation. In this case, "ISW BUSY" will be indicated in
the message area on the display lower right, and the interswitch operation is not
available.
Alarm Sound Control
The interseitch alarm continues to sound for about 5 seconds. In setting the alarm sound
level, open the Sub1 Menu, press [2] switch to select the "5.BUZZER" in LEVEL Menu.
When stopping the alarm sound immediately after it sounds, press [ALARM ACK] switch.
Even when the alarm sound stops, a certain message will remain in the message area.
Notes on Master/Slave Connection
The Master/Slave connection is a configuration in which the Display Unit connected to the
Scanner Unit is the Master Unit, while the Display Unit connected to the Master Unit is a
Slave Unit. Of the interswitch patterns, the following pattern numbers includes the
Master/Slave connection:
a) 2-unit System: No.3, No.4, No.5 and No.6
b) 3-unit System: No.4, No.5, No.6, No.7, No.8, No.9, No.10 and No.11
If the Master Display Unit is not in the transmission state, it is impossible to set the Slave
Display Unit to the transmission state, If the Master Display Unit is changed from the
transmission to the standby mode, the Slave Display Unit will also be set to the standby
mode forcibly. In this status, "MTR ST-BY" will be indicated in the message area and the
alarm will beep.
328


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRC JMA9923_7XA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRC JMA9923_7XA in the language / languages: English as an attachment in your email.

The manual is 7,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info