700456
4
Zoom out
Zoom in
Previous page
1/20
Next page
4 | JL Audio - XD600/1v2 Owners Manual
PRODUCT DESCRIPTION
The XD600/1v2 is a monoblock
amplifier utilizing JL Audio NexD™ high speed
switching technology to deliver outstanding
fidelity and efficiency.
The XD600/1v2 can be operated with a wide
variety of source units and system configurations.
Its frequency response is limited to the range
below 500 Hz. It is not designed for driving
midrange speakers or tweeters. Every aspect of its
operation has been optimized for low-frequency
amplification. For detailed specifications, please
refer to Appendix C (page 13).
TYPICAL INSTALLATION SEQUENCE
The following represents the sequence
for a typical amplifier installation, using an
aftermarket source unit or OEM Interface
processor (like the CleanSweep CL441dsp).
Additional steps and different procedures may
be required in some applications. If you have any
questions, please contact your authorized
JL Audio dealer for assistance.
1) Disconnect the negative battery post
connection and secure the disconnected cable
to prevent accidental reconnection during
installation. This step is not optional.
2) Run 4 AWG power wire from the battery
location to the amplifier mounting location,
taking care to route it in such a way that it will
not be damaged and will not interfere with
vehicle operation. Use 4 AWG or larger power
wire and a fused power distribution block if
additional amplifiers are being installed with
the XD600/1v2.
3) Connect the power wire to the positive battery
post. Fuse the wire with an appropriate fuse
block (and connectors) within 18 inches (45
cm) wire length of the positive battery post.
This fuse is essential to protect the vehicle.
Do not install the fuse until the power wire
has been securely connected to the amplifier.
4) Run signal cables and remote turn-on wire
from the source unit to the final amplifier
mounting location.
5) Run speaker cables from the speaker systems
to the amplifier mounting location.
6) Find a good, solid metal grounding point
close to the amplifier and connect the
negative power wire to it using appropriate
hardware (use of the JL Audio ECS master
ground lug, XB-MGLU is recommended). Use
4 AWG wire, no longer than 36 inches (90 cm)
from the amplifier to the ground connection
point. In some vehicles, it may be necessary to
upgrade the battery ground wire. (See page 5
for important notice).
7) Securely mount the amplifier.
8) Connect the positive and negative
power wires to the amplifier. A fuse
near the amplifier is not necessary if
the XD600/1v2 is the only device being
run from the fused main power wire.
If the fused main power wire is shared
by the XD600/1v2 and other amplifiers
or devices, fuse each amplifier/device
within 12 inches (30 cm) of wire length,
via a fused distribution block or multiple
individual fuse blocks/on-board fuses.
9) Connect the remote turn-on wire to the
amplifier or configure the “Turn-On Mode
switch for automatic turn-on.
10) Connect the input cables to the amplifier.
11) Connect the speaker cables to the amplifier.
12) Carefully review the amplifier’s control
settings to make sure that they are set
according to the needs of the system.
13) Install the power wire fuse (50A for a single
XD600/1v2) and reconnect the negative
battery post terminal. Install the fuse (50A)
near the amplifier (if applicable).
14) Turn on the source unit at a low level to
double-check that the amplifier is configured
correctly. Resist the temptation to crank it up
until you have verified the control settings.
15) Make necessary adjustments to the
input sensitivity controls to obtain the
right overall output and the desired
balance in the system. See Appendix
A (page 12) for the recommended
input sensitivity setting method.
16) Enjoy the fruits of your labor with your
favorite music.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio XD600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio XD600 in the language / languages: English as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info