700505
2
Zoom out
Zoom in
Previous page
1/4
Next page
2 JL AUDIO MX10IB3
A
C
B
E
D
We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers.
We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely
affect performance.
All specifications are subject to change without notice.
PHYSICAL SPECIFICATIONS
Subwoofer Physical Specifications
Nominal Diameter: 10 in. / 250 mm
Overall Diameter (A): 10.75 in. / 273 mm
Mounting Hole Diameter (B): 8.875 in. / 225 mm
Bolt Hole Circle (C): 9.706 in. / 247 mm
Motor Overmold Outer Diameter (D): 5.29 in. / 134 mm
Mounting Depth (E): 5.12 in. / 130 mm
Net Weight: 6.5 lbs. / 2.94 Kg
Driver Displacement: 0.04 ft
3
/ 1.13 litres
Subwoofer Parameters MX10IB3
Free Air Resonance (Fs): 41.84 Hz
Electrical “Q” (Qes): 0.806
Mechanical “Q” (Qms): 11.751
Total Speaker “Q” (Qts): 0.754
Equivalent Compliance (Vas): 1.29 ft
3
/ 36.53 litres
One-way, Linear Excursion (Xmax)*: 0.42 in. / 10.7 mm
Efficiency (1W/1m)**: 87.23 dB SPL
Effective Piston Area (Sd): 50.68 in² / 0.0327 m²
DC Resistance (Re): 3.957 ohm
Nominal Impedance: 4 ohm
Infinite Baffle Use: Yes
Enclosure Use: Yes (Sealed Only)
Power Handling (continuous): 175W
* Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.
** Efficiency (1W/1m) is not an accurate indicator of a subwoofer’s output capability and should not be used
as a comparison to other subwoofers to determine which one is “louder” !
INSTALLATION PROCEDURE
The diagram above shows the typical
installation procedure into a fiberglass panel using
the supplied hardware (Classic Grille Model shown.
Installation is the same for Sport Grille Models).
Always follow proper safety procedures when
working on a vessel. Use eye-protection at all times
and a dust mask and gloves when cutting.
1) Choose a flat mounting surface that has
sufficient
depth and air space behind it to accept
the subwoofer.
2) Cut a 8.875-inch (225 mm) diameter hole.
3) Run the speaker cable to the mounting location.
4) Place the woofer in the hole and mark the screw
hole locations using a sharp, pointed tool.
5) Remove the woofer and drill a pilot hole
(see chart on next page) in each of the screw
locations. It is also advisable to use a hand-driven
countersink tool on each hole to further inhibit
gel-coat cracking of fiberglass panels.
6) Connect the speaker wires and place the woofer,
with its grille in place, into the opening (for Sport
Grille models, pay attention to where the logo
badge will added.
7) While holding the speaker firmly in its mounting
location, evenly snug the mounting screws in a
criss-cross pattern, then hand tighten in a criss-
cross pattern.
Non-standard installations may require different
hardware. Always use marine-grade, stainless-steel
fasteners to ensure a secure, reliable installation.
INCLUDED PARTS
• One Polymer Subwoofer Grille
Six #8 x 1 1/2-inch (38 mm) pan-head
stainless-steel screws for speaker mounting
Six #8 stainless-steel washers for speaker mounting
• Logo Badges (Sport-Grille Models Only)
One Pair Black (White, Titanium/Black &
Chrome Models)
One Pair Red (White, Titanium/Black &
Chrome Models)
One Pair Titanium (Titanium/Black Models Only)
One Pair White (White Models Only)
One Pair Blue (Chrome Models Only)
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio MX10IB3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio MX10IB3 in the language / languages: English as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info