700442
5
Zoom out
Zoom in
Previous page
1/24
Next page
5
TYPICAL INSTALLATION SEQUENCE
The following represents the sequence for
a typical amplifier installation, using an
aftermarket source unit or OEM Interface
processor (like the CleanSweep® CL441dsp).
Additional steps and different procedures may
be required in some applications. If you have
any questions, please contact your authorized
JL Audio dealer for assistance.
1) Disconnect the negative battery post
connection and secure the disconnected cable
to prevent accidental re-connection during
installation. This step is not optional!
2) Run power wire from the battery location
to the amplifier mounting location, taking
care to route it in such a way that it will
not be damaged and will not interfere with
vehicle operation. 4 AWG is recommended
for wire runs greater than 72 inches (180
cm) in length. Use of 8 AWG power wire is
acceptable for shorter runs, such as from a
power distribution block to the amplifier or
from a trunk-mounted battery. Use a 2 AWG
or 1/0 AWG main power wire with a power
distribution block when additional amplifiers
are being installed with the HD750/1 and
powered from the same main power wire.
3) Connect power wire to the positive battery
post. Fuse the wire with an appropriate fuse
block (and connectors) within 18 inches (45
cm) wire length of the positive battery post.
This fuse is essential to protect the vehicle.
Do not install the fuse until the power wire
has been connected to the amplifier.
4) Run signal cables (RCA cables) and remote
turn-on wire from the source unit or interface
processor to the amplifier mounting location.
5) Run speaker wire from the speaker systems to
the amplifier mounting location.
6) Find a good, solid, bare metal grounding
point close to the amplifier and connect the
negative power wire to it using appropriate
hardware. Use minimum 8 AWG power wire,
no longer than 36 inches (90 cm) or 4 AWG
wire up to 60 inches (150 cm) long from the
amplifier to the ground connection point. In
some vehicles, it may be necessary to upgrade
the battery’s ground wire as well. (See pages 6,
7 for important notice).
7) Securely mount the amplifier using
appropriate hardware. (See page 8 for detailed
mounting instructions).
8) Connect the remote turn-on wire and the
positive and negative power wires to the
amplifiers power connector plug. Then insert
the power connector plug into the amplifiers
power connector receptacle, pushing firmly.
9) Connect the RCA input cables
to the amplifier.
10) Connect the speaker wires to the speaker
connector plug and insert the plug firmly into
the speaker connector receptacle.
11) Carefully review the amplifier’s control
settings to make sure that they are set
according to the needs of the system.
12) Install power wire fuse (60A for a
single HD750/1) and reconnect the negative
battery post terminal.
13) Turn on the source unit at a low level
to double-check that the amplifier is
configured correctly. Resist the temptation
to crank it up until you have verified the
control settings.
14) Make necessary adjustments to the input
sensitivity controls to obtain the right
overall output and the desired balance
in the system. See Appendix C (pages 18, 19)
for the recommended input sensitivity
setting method.
15) Enjoy the fruits of your labor with your
favorite music.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio HD750 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio HD750 in the language / languages: English as an attachment in your email.

The manual is 1,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info