700446
10
Zoom out
Zoom in
Previous page
1/13
Next page
18 | JL Audio - 1200/1v3 Owners Manual
19
3) The input sensitivity of the two amplifiers
needs to be adjusted independently. To
properly calibrate the amplifiers for
maximum, identical, clean output, please
refer to Appendix A (page 14). After using this
procedure, you can then adjust the level of the
amplifiers by adjusting the input sensitivities
downward, if the amplifiers require attenuation
to achieve the desired system balance. If the
input sensitivities are adjusted, the amplifiers
must be recalibrated to ensure identical power
output levels.
Note: TheInput Range” switch on all “Slave
amplifiers needs to be set to “Low”, even if
the “Master” amplifier is high voltage and its
switch is set to High. All signals passed out
of the preamp outputs of the amplifier are
compatible with the “Low” setting on the “Input
Range” control.
4) If you would like to run a third amplifier
in “Slave” configuration, select the “Full-
Range” position on the “Output Mode
switch of the first “Slave” amplifier. Then,
connect an RCA cable from the first
“Slave” amplifier’s preamp outputs to the
second “Slave” amplifier. As you did with
the first “Slave” amplifier, set the second
“Slave” amplifier’s “Amp LP Filter” to the
Off” position. Then, calibrate the third
amplifier’sInput Range” and Input
Sens.” controls in the same manner as you
did for the second amplifier.
Additional amplifiers may be added to this
“Master/Slave” configuration following the same
procedure as in step 4.
Once you match the input sensitivities of
all the amplifiers, you can use the “Master
amplifier’sAmp LP Filterand “Advanced
Bass Controlfeatures to control the “Slave
amplifier(s). If the remote bass control (RBC-1) is
used, it need only be connected to the “Master
amplifier to control all the amplifiers in the
“Master/Slave” chain.
Reference the diagram showing a “Master/
Slave” configuration with one “Master” (top
amplifier) and two “Slave” amplifiers. Switches
and controls that are defeated in the “Slave”
amplifiers are printed in gray.
APPENDIX D:
Master/Slave Configurations
With the flexible on-board crossovers and
processing incorporated into the 1200/1v3, it
is possible to connect multiple 1200/1v3’s in a
“Master/Slave” configuration, with each amplifier
driving its own speaker system but controlled by
the processing and filtering of only one amplifier.
This is very useful when driving multiple
subwoofers with multiple amplifiers.
To create a Master/Slave configuration, first
determine which amplifier will be the “Master”
amplifier and connect the main input signal to
that amplifier (from the source unit or from an
outboard processor). This amplifier’s “Amp LP
Filter” section and Advanced Bass Control
features will process the signal for the “Slave”
amplifier or amplifiers.
Here is the procedure for implementing a
“Master/Slave” configuration:
1) Set the “Master” amplifier’s “Output Mode
switch to the center “Amp Filterposition.
This will send a parallel, mono-summed signal
from the “Master” amplifiers Amp LP Filter
section to its preamp outputs.
2) Connect an RCA cable from the “Master”
amplifier’s preamp outputs to the main input
of the first “Slave” amplifier. Set the “Slave
amplifier’sAmp LP Filterto the Off
position. This will defeat the LP filter and the
bass processing of this “Slave” amplifier.
MASTER:
+12VDC Ground Remote
Preamp Output Section Infrasonic Filter “Q Center Freq. Boost (dB) Amp LP Filter
Advanced
Bass
Control
Amplifier Input Section Subwoofer Output
MONO OUTPUT ONLY
Left Output Right Output Left Ch. Right Ch.Filter Freq. (Hz) Filter Freq. (Hz)Infrasonic Freq. (Hz) Remote Bass Port
Full Range
|
Amp Filter
|
Out Filter
Output Mode Filter Slope Mode Mode
|
Slope Input Voltage Input Sens.
Output Polarity
12dB
|
24dB
Filter Mode
LP
|
HP
Bass EQ
Off
|
On
Off
|
12dB
|
24dB Low
|
High
Normal
|
Reversed
Off
|
On
40
45
55
65
85
120
200 15
18
25
30
40
50
60 40
45
55
65
80
100
200
0.5
0.7
1.1
1.6
2.7
4.3
20
25
35
45
55
70
80 0
+4
+10
+13
+15
120 0 /1v3
Monoblock Subwoofer Amplifier
+12VDC Ground
Preamp Output Section Infrasonic Filter “Q Center Freq. Boost (dB) Amp LP Filter
Advanced
Bass
Control
Amplifier Input Section Subwoofer Output
MONO OUTPUT ONLY
Left Output Right Output Left Ch. Right Ch.Filter Freq. (Hz) Filter Freq. (Hz)Infrasonic Freq. (Hz) Remote Bass Port
Full Range
|
Amp Filter
|
Out Filter
Output Mode Filter Slope Mode Mode
|
Slope Input Voltage Input Sens.
Output Polarity
12dB
|
24dB
Filter Mode
LP
|
HP
Bass EQ
Off | On
Off
|
12dB
|
24dB Low
|
High
Normal
|
Reversed
Off
|
On
40
45
55
65
85
120
200 15
18
25
30
40
50
60 40
45
55
65
80
100
200
0.5
0.7
1.1
1.6
2.7
4.3
20
25
35
45
55
70
80 0
+4
+10
+13
+15
120 0 /1v3
Monoblock Subwoofer Amplifier
Remote
Set all amps in chain to "Normal" OR
Set all amps in chain to "Reversed"
!
IMPORTANT
+12VDC Ground Remote
Preamp Output Section Infrasonic Filter “Q Center Freq. Boost (dB) Amp LP Filter
Advanced
Bass
Control
Amplifier Input Section Subwoofer Output
MONO OUTPUT ONLY
Left Output Right Output Left Ch. Right Ch.Filter Freq. (Hz) Filter Freq. (Hz)Infrasonic Freq. (Hz) Remote Bass Port
Full Range
|
Amp Filter
|
Out Filter
Output Mode Filter Slope Mode Mode
|
Slope Input Voltage Input Sens.
Output Polarity
12dB
|
24dB
Filter Mode
LP
|
HP
Bass EQ
Off | On
Off
|
12dB
|
24dB Low
|
High
Normal
|
Reversed
Off
|
On
40
45
55
65
85
120
200 15
18
25
30
40
50
60 40
45
55
65
80
100
200
0.5
0.7
1.1
1.6
2.7
4.3
20
25
35
45
55
70
80 0
+4
+10
+13
+15
120 0 /1v3
Monoblock Subwoofer Amplifier
Connect Master 1200/1 Preamp Output to Slave A 1200/1 Input
Connect Slave A 1200/1 Preamp Output to Slave B 1200/1 Input
Connect Master 1200/1 Input to Signal Source
Make sure that the "Output Polarity"
switches are in the same position for
all the ampliers in a master/slave chain.
The Master amplifier’s
Advanced Bass Control” section
is active and affects all three
amplifiers equally.
The last Slave amplifier’s
Advanced Bass Control”
section, AMP LP Filter and
“Preamp Output”
are inactive.
This Slave amplifier’s
Advanced Bass Control” section
and AMP LP Filter are inactive,
but the Full-Range (pass-
through) feature of its “Preamp
Output” feeds the input of the
next Slave amplifier.
SLAVE A:
SLAVE B:
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JL Audio 1v3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JL Audio 1v3 in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info