509190
1
Zoom out
Zoom in
Previous page
1/5
Next page
Figure A
Introduction
Thank you for choosing a Jensen product.
The JWR200 Marine Wired Remote Control
allows you to control basic functions of
Jensen Marine JMS series radios, including
power, mode, volume, tuning and CD, iPod
and satellite radio operation.
Installation
1. Choose a mounting location on the
instrument panel that will allow enough
room behind the panel to run the wired
remote cables to the existing radio.
2. Cut a hole in the instrument panel using
the supplied template. At least 2 ½" depth
is needed to mount the remote control.
Important: Do not mount unit where it
can be submerged or subjected to high
pressure spray.
3. Insert the remote control into the hole and
then secure from the other side using the
threaded ring, illustrated in Figure A.
Wiring
Once the remote has been mounted, route the
cable from the remote and connect the cable
to the radio. Note the connector polarity on
the extension cable. The 18 foot extension
cable may be used to connect the remote to
the radio. Up to two additional extension
cables (JWREXT) may be purchased and
used to extend the reach of the remote up to
54 feet. Important: When connecting the
cables, be sure to route the extension cable
away from sharp objects, corners, and places
where it might get pinched, as this could
affect performance and cause damage to the
unit. Up to two more remote controls can be
added with a "Y" cable adapter
(JWRYCBLS).
Introducción
Gracias por seleccionar un producto de
Jensen. El control remoto atado con alambre
marina JWR200 permite que usted controle
funciones básicas de las radios de marina
JMS de Jensen, incluyendo energía, modo,
volumen, iPod, del CD y la operación de
radio del satélite.
Instalación
1. Seleccione una localización del montaje
en el tablero de instrumentos que
permitirá bastante sitio detrás del panel de
funcionar los cables alejados atados con
alambre a la radio existente.
2. Corte un agujero en el tablero de
instrumentos usando la plantilla provista.
Profundidad por lo menos del la 2 1/2 " es
necesaria montar el control remoto.
Importante: No arme la unidad en un
lugar donde se pueda hundir o sujetado al
aerosol de alta presión.
3. Inserte el control remoto en el agujero y
después asegúrelo del otro lado usando el
anillo roscado, ilustrado en la Figure A.
Cableado
El remote controlo se ha montado, encamina
el cable del remote controlo y conecta una
vez el cable con la radio. Observe la
polaridad del conectador en el cable de la
extensión. El cable de la extensión de 18 pies
se puede utilizar para conectar el remote
controlo con la radio. Hasta dos cables
adicionales de la extensión (JWREXT) se
pueden comprar y utilizar para prolongar el
alcance del remote controlo hasta 54 pies.
Importante: Al conectar los cables, sea seguro
encaminar el cable de la extensión lejos de
objetos, de esquinas, y de los lugares agudos
en donde puede ser que consiga pellizcado,
pues éste podría afectar funcionamiento y
causar daño a la unidad. Hasta dos mandos
más a distancia se pueden agregar con un
adaptador del cable de "Y" (JWRYCBLS).
Introduction
Merci d'avoir choisi un produit Jensen. La
télécommande branchée Marine JWR200
vous permet de contrôler les fonctions de
base des radios marines JMS Jensen, y
compris la puissance, la mode, le volume, la
syntonisation et l'opération CD, iPod et radio
satellite.
Installation
1. Choisissez un emplacement de montage
sur le panneau d'instruments qui vous
laissera assez de place derrière le panneau
pour brancher les câbles à distance à la
radio existante.
2. Faites un trou dans le panneau
d'instrument en utilisant le modèle fourni.
Une profondeur d'au moins 2 1/2'' est
exigé pour monter la télécommande.
Important : Ne montez pas l'appareil là où
il peut être submergé ou est exposé à des
embruns de haute pression.
3. Insérez la télécommande dans le trou et
puis l'attacher de l'autre côté en utilisant la
bague filetée, comme illustré dans la
Figure A.
Câblage
Lorsque vous avez fini de monter la
télécommande, faites traverser le câble depuis
la télécommande et branchez le câble à la
radio. Le câble d'extension de 18 pieds peut
être utilisé pour brancher la télécommande à
la radio. Vous pouvez acheter jusqu'à deux
câbles d'extension (JWREXT) pour étendre la
portée de la télécommande jusqu'à 54 pieds.
Lorsque vous branchez les câbles, assurez-
vous que vous faites traverser le câble loin
des objets fins, des coins et des endroits où il
peut être pincé, comme cela peut avoir un
effet sur la performance et endommager
l'appareil. Jusqu'à deux télécommandes
peuvent être ajoutées avec un adapteur de
câble d'Y (JWRYCBLS).
JWR200 Wired Remote
Installation Instructions
www.asaelectronics.com © 2010
POWER
JWR200
MODE
ENTER
CAT
DISP
VOL+
UP
VOL-
DN
BAND
WB
MUTE
>
>>
>>
Power
Potencia
Alimentation
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jensen JWR200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jensen JWR200 in the language / languages: English as an attachment in your email.

The manual is 0,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info