648492
12
Zoom out
Zoom in
Previous page
1/14
Next page
GTR AMPLIFIERS
Setting the input level controls
To match your amplifier’s input sensitivity (gain) to your source unit’s output level, we recommend the following procedure:
A. Turn both input level controls counterclockwise to MIN (minimum).
B. Play a dynamic music track through your source unit. Turn the source unit’s volume control to the 3/4 position.
C. Turn front input level control dial clockwise towards MAX until it no longer sounds clear and there are crackling, crunching, hissing or other types of
distortion interfering with the distinct sounds of a musical instrument.
D. Slowly turn the front level input control dial counterclockwise until the music sounds clear again, then note or mark where the dial is. That mark is now
your maximum volume setting for clear audio.
E. Your front input level is now correctly set. Repeat this process with the rear channels.
Setting the crossover (GTR-102, GTR-104, GTR-7535)
Properly setting crossover filter selectors optimizes frequency distribution for efficient speaker operation and best sound.
Step 1: Use the slider controls to select low-pass (LP), FULL, or high-pass (HP).
LP: Low pass. Choose this setting if you are connecting a subwoofer(s) or want to provide a low-pass filter for separate mid-bass speakers. NOTE: the
GTR-601 and GTR 1001 feature low-pass crossovers only.
FULL: Full range. Choose this setting if you are connecting full-range speakers and are not using a subwoofer in your system.
HP: High pass. Choose this setting to prevent low bass from reaching midrange or full-range speakers when you are using a subwoofer in your system.
Step 2: Use crossover-filter frequency controls to adjust crossover point settings for coaxial speakers and subwoofers to suit listener preference. Turn the
dials to the left to lower the crossover point and to the right to raise the crossover point. Exact crossover settings for coaxial speakers and subwoofers finally
depend on your listening preferences. NOTE: crossover point does not apply in FULL mode.
Adjusting the subwoofer
Select INT if you’re connecting a subwoofer to the GTR-7535 amplifier and if your source unit does not feature a subwoofer
output (this will send a summed audio signal to the subwoofer). If your source unit does feature a subwoofer output, select
EXT to connect to that output.
Selecting subwoofer Phase (GTR-601, GTR-1001, GTR-7535)
You can choose a subwoofer phase output of 0° or 180°. To check your sub’s phase, play music with lots of bass and listen
as another person slowly flips the 0/180 degree phase switch back and forth. The correct setting is the one that gives you
more bass. If you don’t detect any real difference, leave the switch in the O setting.
Bass Boost EQ (GTR-601, GTR-1001, GTR-7535)
Bass Boost EQ gives you the ability to increase the bass output from 0 dB to +12 dB.
BASS BOOST
0dB +12dB
A B C D E
PHASE
180º
SUB INPUT
INT EXT
9
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL GTR-102 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL GTR-102 in the language / languages: English as an attachment in your email.

The manual is 1,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JBL GTR-102

JBL GTR-102 User Manual - German - 23 pages

JBL GTR-102 User Manual - Dutch - 23 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info