809548
10
Zoom out
Zoom in
Previous page
1/12
Next page
10
pROBLEM SOLUtION
If there is no sound from any of the
speakers:
Check that receiver/amplifier is on and a source is playing.
Check that the powered subwoofer is plugged in and is turned on (Power
switch å pushed in).
Check all wires and connections between receiver/amplifier and speakers.
Make sure all wires are connected. Make sure none of the speaker wires are
frayed, cut, punctured or touching each other.
Review proper operation of your receiver/amplifier.
If there is no sound coming from one
speaker:
Check the Balance control on your receiver/amplifier.
Check all wires and connections between receiver/amplifier and speaker.
Make sure all wires are connected. Make sure none of the speaker wires are
frayed, cut, punctured or touching each other.
In Dolby Digital or DTS modes, make sure that the receiver/amplifier is
configured so that the speaker in question is enabled.
Turn off all electronics, and switch the speaker in question with one of
the other speakers that is working correctly. Turn everything back on, and
determine whether the problem has followed the speaker or has remained in
the same channel. If the problem is in the same channel, the source of the
problem is most likely with your receiver or amplifier, and you should consult
the owner’s manual for that product for further information. If the problem has
followed the speaker, consult your dealer for further assistance or, if that is
not possible, visit www.jbl.com.
If there is no sound from the center
speaker:
Check all wires and connections between receiver/amplifier and speaker.
Make sure all wires are connected. Make sure none of the speaker wires are
frayed, cut, punctured or touching each other.
If your receiver/processor is set in Dolby Pro Logic mode, make sure the
center speaker is not in phantom mode.
If your receiver/processor is set in one of the Dolby Digital or DTS modes,
make sure the receiver/processor is configured so that the center speaker is
enabled.
If the system plays at low volumes but
shuts off as volume is increased:
Check all wires and connections between receiver/processor and speakers.
Make sure all wires are connected. Make sure none of the speaker wires are
frayed, cut, punctured or touching each other.
If more than one pair of main speakers is being used, check the minimum
impedance requirements of your receiver/amplifier.
If there is low (or no) bass output: Make sure the connections to the left and right speaker inputs have the
correct polarity (+ and –).
Make sure the subwoofer is plugged into an active electrical outlet and is
turned on (Power switch å pushed in).
In Dolby Digital or DTS modes, make sure your receiver/processor is
configured so that the subwoofer and LFE output are enabled.
Switch the Phase switch ç to the opposite position, and select the position
that results in the most pleasing bass response.
If there is no sound from the surround
speakers:
Check all wires and connections between receiver/processor and speakers.
Make sure all wires are connected. Make sure none of the speaker wires are
frayed, cut, punctured or touching each other.
Review the proper operation of your receiver/amplifier and its surround-sound
features.
Make sure the movie or TV show you are watching is recorded in a surround
sound mode. If it is not, check to see whether your receiver/processor has
other surround modes you may use.
In Dolby Digital or DTS modes, make sure your receiver/processor is
configured so that the surround speakers are enabled. When five satellites
are in use, remember to configure your receiver or processor for 6.1-channel
operation, and when six satellites are in use, configure your receiver or
processor for 7.1 channels.
Review the operation of your DVD player and the jacket of your DVD to make
sure that the DVD features the desired Dolby Digital or DTS mode, and that
you have properly selected that mode using both the DVD player’s menu and
the DVD disc’s menu.
tROUBLEShOOtINg
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL CINEMA SOUND CSB6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL CINEMA SOUND CSB6 in the language / languages: English as an attachment in your email.

The manual is 1.82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info