648498
3
Zoom out
Zoom in
Previous page
1/38
Next page
EN
THANK YOU
for choosing the JBL BassPro. BassPro has been designed to
provide the kind of high-performance low-frequency reproduction
that used to require big, clumsy enclosures, large amplifiers, and
complex installation. To ensure maximum performance, we
strongly recommend that installation be entrusted to a qualified
professional.
WARNING
Playing loud music in an automobile can permanently damage
your hearing as well as hinder your ability to hear traffic. We
recommend using low volume levels while driving. Harman
International accepts no liability for hearing loss, bodily injury or
property damage resulting from the use or misuse of this product.
INSTALLATION
Choosing a mounting location
Choose a location that doesn’t interfere with the loading or
unloading of cargo, fold-down rear seats, or opening or closing of
the trunk lid. The best location is likely to be the front or rear
corner of the trunk or luggage compartment. These locations, in
addition to being out of the way, will provide the best sonic
reproduction in the 60Hz – 100Hz range because the output of
the woofer will be “corner loaded” against the walls of the vehicle.
In any case, the BassPro must not interfere with the safe
operation of the vehicle.
CAUTION: Make sure mounting screws will not puncture wiring
harnesses, brake or fuel lines, or the vehicle’s fuel tank. Some or
all of these may be located behind or under the mounting surface.
Mounting BassPro
IMPORTANT: Disconnect the vehicle’s negative (–) battery
terminal before beginning the installation.
NOTE: If you are using only the BassPro’s line-level (RCA) inputs,
you must connect the remote wire from the BassPro to the
system’s head unit so BassPro will turn on and off with the
system. If you will be using the speaker-level outputs from your
head unit, you do not need to connect the remote output. The
BassPro’s speaker-level inputs will sense voltage on the speaker
wires and the BassPro will turn itself on. (See Audio Sense
Switch, below.)
Input Connections
Connect the subwoofer output from the
source unit to either the left or right
line-level input. If your source unit does
not have a dedicated subwoofer output
you can connect the rear left/right
outputs to the BassPro’s left and right
inputs.
If your source unit doesn’t have
line-level outputs you can use the
included speaker-level input harness to
connect the BassPro to the source
unit’s speaker outputs. See the
illustration for the wiring configuration.
Power
Connectors
Audio System
Head Unit
BassPro
Chassis Ground
(bare metal)
18”
(46cm)
20A Fuse
Remote Turn-On (optional)
>#18AWG (0.82mm
2
) Wire
>#12AWG (2.05mm
2
) Wire
>#12AWG (2.05mm
2
) Wire
CONNECTIONS
Power Connections
L+ R+
L– R–
BassPro
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL BassPro SL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL BassPro SL in the language / languages: All languages as an attachment in your email.

The manual is 9,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info